START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Blade 400 Blade Helicopters (eFlite) 400 Helicopters |
|
LinkBack | Thread Tools | Display Modes |
02-03-2009, 09:13 AM | #1 (permalink) |
Registered Users
|
Another Head and Main bolt supplier
FYI
Found these guys at my LHS. They are the 2mm x 12 (4 pack) by DUBRO Racing in the airplane servo section. Same size as the head and main bolt on the stock B400 head and shaft. JFYI,, Just thought I would let everyone know in case they cant wait on shipping..
__________________
BLADE 400, SPEKTRUM 6I,GY401B, HS65MG'S, CYCLIC, DSP285 TAIL, CASTLE BEC |
Sponsored Links | |||
Advertisement |
|
02-03-2009, 09:13 AM | #2 (permalink) |
Registered Users
Thread Starter
|
oh yea. they were $1.79...
__________________
BLADE 400, SPEKTRUM 6I,GY401B, HS65MG'S, CYCLIC, DSP285 TAIL, CASTLE BEC |
02-03-2009, 09:14 AM | #3 (permalink) |
Registered Users
|
I ordered a box of 50 for 6 bucks and some change. I know prices went up since but I doubt much.
__________________
Blade 400 3x DS285MG, DS290G Tail, G2703D Gyro, Trex 500 skids, motor-none, ESC-none, estimated finish date-unsure Trex 250 aka the crash test dummy |
02-03-2009, 09:17 AM | #4 (permalink) |
Registered Users
|
I was way off!!! $9.45 for a box of 100 in stainless comes out to .09 cents a screw.
__________________
Blade 400 3x DS285MG, DS290G Tail, G2703D Gyro, Trex 500 skids, motor-none, ESC-none, estimated finish date-unsure Trex 250 aka the crash test dummy |
02-03-2009, 09:18 AM | #5 (permalink) |
Registered Users
Thread Starter
|
where at?
__________________
BLADE 400, SPEKTRUM 6I,GY401B, HS65MG'S, CYCLIC, DSP285 TAIL, CASTLE BEC |
02-03-2009, 09:34 AM | #6 (permalink) |
Registered Users
|
I think the black one are stronger than stanless. stanless is harder and snaps easer i belive
|
02-03-2009, 02:37 PM | #7 (permalink) | |
Registered Users
Join Date: Jul 2008
|
Quote:
Stainless is softer and shears easier, unless of course you buy graded bolts, but you ain't gonna get em for .99 cents. Thanks for tip mobilecal
__________________
Blade CX2, Blade 400, Nano CPX |
|
02-03-2009, 03:14 PM | #8 (permalink) | |
Registered Users
|
Quote:
McMasterCar.com
__________________
Blade 400 3x DS285MG, DS290G Tail, G2703D Gyro, Trex 500 skids, motor-none, ESC-none, estimated finish date-unsure Trex 250 aka the crash test dummy |
|
02-03-2009, 04:56 PM | #9 (permalink) |
HF Support
|
You can also get small packs of many M2&M3 sizes at ReadyHeli, HeliDirect and RTL Fasteners.
__________________
Jonathan Livingston Helicopter Blade 400: E-flite 420H/35X ESC, AR6100e, HS65HB x 3, G401B/DS290G. (Ret.) CopterX 450AE V2: 430XL/35X ESC, AR6100, HS65HB x 3, LTG2100T/HSG-5084MG. T-Rex 550E V1 Classic Flybar: 600MX/BL70G, AR6200, DS610 x 3, Quark/DS650, 16t/520mm blades. |
02-03-2009, 05:08 PM | #10 (permalink) |
Registered Users
|
especially if you are there ordering parts you might as well add a box of the 2mm screws since your paying the shipping anyway.
__________________
Blade 400 3x DS285MG, DS290G Tail, G2703D Gyro, Trex 500 skids, motor-none, ESC-none, estimated finish date-unsure Trex 250 aka the crash test dummy |
02-03-2009, 05:59 PM | #11 (permalink) |
Registered Users
|
I have sheared the stock bolts right off more than once. I use Aspect Aviation hardware now. It seems like a softer material. They bend but have never sheared off
__________________
Compass 7HVU HBL980/950 Ar7200bx Edge160-- Compass 6HV, 610/650
TRex 700LE , Beastx 610/650, Warp360 TracX 92A+ |
Thread Tools | |
Display Modes | |
|
|