Stratus bearing size - list

[misio]

I’m trying to make a list of all bearings that stratus need for replacement. So far I was able to get this. If any one knows bearing size please post and I will update list

120-12 upper main shaft bearings block – 2x 10-19-5mm
120-8 main shaft/tail drive bearing block – 10-19-5mm + 2x 5-10-5
115-18 lower main shaft bearing block – 2x 10-19-5mm
126-66 front T/R bearing block – ? flanged

Clutch bell unit
Bearing block –
Upper 111-8 – 6x17 flange
Middle 0199- 6x19x5
Lower 0183 – 10x19x5
Driver bearing big one 10x19x7
Clutch bell 6x10x5 - flanged

Blade grip - 2 each 8x16x5 plus thrust bearing
Flybar carrier/pivots in the head 4 - 6x10x3 Flanged

Tork tube – 1 or 2 9.5mm x 15.8mm

Bellcrank bearings
6x M3x7x3 Flanged
2x M5 ? Flanged

If you have any info please post and I will updates list for every one, I will add size for open box, head etn.

[ChrisLaFollette]

The bearing in the clutch bell is a 6x10x5.

Blade grips are 8x16x5, 2 in each grip and a thrust bearing in each grip.

The bearing that the pinion inserts into, the one in the bottom of the bearing block is a 10x19x5.

I know pretty much all the dimensions by heart and I will get back later with the rest of the dimensions.

[misio]

Thanks for that info, list is updated, stylle need more

Driver bearing bethen driver and clutch ( big one )

tork tube ?

126-66 front T/R bearing block – ? flanged

[angelob]

The flybar carrier and pivots in the head are 6x10x3 flanged - qty 4

[ChrisLaFollette]

Heres a full list.

All mainshaft bearings are 10x19x5 bearings non flanged

Main Grip bearings are 8x16x5 non flanged

New flybar carrier and carrier pivot bearings are 6x10x3 flanged

Clutch bell bearing is 6x10x5 non flanged

Top clutch block stack bearings is 6x17x5 flanged

Middle bearing is 6x19x5 non flanged

Lower is 10x19x5 non flanged

Driver bearing is 10x19x7 non flanged

Torque Tube bearing is 9.5x16.. er like 15.8 actually x 4 non flanged

All I know off the top of my head. I dont have the one piece block for the middle mainshaft bearing block with the front drive gear bearing thing.

[misio]

thanks for info
Torque Tube bearing is 9.5x16.. er like 15.8 actually x 4 non flanged ???



and one more for now http://www.ronlund.com/images/ma/ma126-66.jpg

[ChrisLaFollette]

The torque tube bearing wasnt quite 16 mm it was actually about 15.8 and the ID was about 9.5.

Measured with calipers.

[rotrap]

The torque tube bearing
Inner diam 3/8 (9.525mm)
Outer diam 5/8 (15.875mm)
Width 5/32 (3.967mm)

R1038

/Henrik

[DavidH]

The thread is nearly 1 1/2 years old. LOL
Chris is no longer around anymore. Look in the Stolen section and you will see why.

David

[rotrap]

The thread is nearly 1 1/2 years old. LOL
Chris is no longer around anymore. Look in the Stolen section and you will see why.

David

I know the thread is old! just trying to help people, as i searched for a while since here in sweden inch bearings isn´t that common ;-)

/Henrik

[DavidH]

MA uses bearings that have metric dimensions. Yes any bearing the size can be posted in inches or millimeters. MA has always used metric measurements for the bearings they use. The bolts are also metric, as is most of the parts on the heli.
Just found it amusing someone would drag out a thread old as this one.

David

[misio]

Just found it amusing someone would drag out a thread old as this one.

David

Just for onec get a beer and be positive with your live.

[DavidH]

I am positive with my life everyday. Waking up each morning is positive. LOL

David