freakinnovice
12-19-2009, 09:22 AM
Mikado Logo 400, with all the major upgrades;
I’m selling this heli just to free up space in my fleet for the 500 I’m building. This heli has very low air time and only one hard landing (poor auto). Of course every thing was replaced or upgraded. You may notice this FB is a bit large. It’s spinning an L600 flybar and paddles and they rock by making it super response on cyclic. Listed below are a few of the addition and changes I’ve made to this heli.
All Bushings Upgraded to Bearings
10mm. Grips w/3mm. Bolt(s)
KBDD 70mm. Tail Blades (Orange)
Hacker A40-10S (8-pole) 1600kv. Motor w/22T. Pinion
Hobbywing 60 ESC
(3) Hyperion DS16FMD’s
(1) Futaba S9254 on the tail
(1) Inertia 860 Gyro.
Custom CF Servo Plate mounted
Protos Landing gear (Gorilla)
Alum Tail Case
Mikado Upgrades include;
Alum. Motor-mount
Alum. Hexagontal frame-bolts
Alum. Swashplate
Alum. Flybar Cage
Alum. Washout-base (ball-raced)
Logo 600 flybar and paddles for extra stability
CF Gyro-mount
Full 3D Tail-rotor assembly w/Thrust-bearings
Painted FG Canopy
Spare-parts included;
(1) part of used (bent) skids
(1) 2mm Flybar and equipment
(1) .5 Mod. Main gear
A hand full of spare parts and wooden blades
I just finished going through this entire Heli inspecting or upgraded all the parts.
$800.00 PayPal /Shipped CONUS
RX not included
If your looking for a less expensive setup I have a 401 and a Hyperion DS20 I can swap out for a few bucks
Sorry about the picture orenitation,
I’m selling this heli just to free up space in my fleet for the 500 I’m building. This heli has very low air time and only one hard landing (poor auto). Of course every thing was replaced or upgraded. You may notice this FB is a bit large. It’s spinning an L600 flybar and paddles and they rock by making it super response on cyclic. Listed below are a few of the addition and changes I’ve made to this heli.
All Bushings Upgraded to Bearings
10mm. Grips w/3mm. Bolt(s)
KBDD 70mm. Tail Blades (Orange)
Hacker A40-10S (8-pole) 1600kv. Motor w/22T. Pinion
Hobbywing 60 ESC
(3) Hyperion DS16FMD’s
(1) Futaba S9254 on the tail
(1) Inertia 860 Gyro.
Custom CF Servo Plate mounted
Protos Landing gear (Gorilla)
Alum Tail Case
Mikado Upgrades include;
Alum. Motor-mount
Alum. Hexagontal frame-bolts
Alum. Swashplate
Alum. Flybar Cage
Alum. Washout-base (ball-raced)
Logo 600 flybar and paddles for extra stability
CF Gyro-mount
Full 3D Tail-rotor assembly w/Thrust-bearings
Painted FG Canopy
Spare-parts included;
(1) part of used (bent) skids
(1) 2mm Flybar and equipment
(1) .5 Mod. Main gear
A hand full of spare parts and wooden blades
I just finished going through this entire Heli inspecting or upgraded all the parts.
$800.00 PayPal /Shipped CONUS
RX not included
If your looking for a less expensive setup I have a 401 and a Hyperion DS20 I can swap out for a few bucks
Sorry about the picture orenitation,