ChiefWilson
04-05-2007, 12:56 AM
Ok I have 2 helicopters to sell I would like to sell them together but will sell individually. I also have a lot of parts with these 2 helicopters. I kind of split the parts up between the 2 of them so it would be equal. on to the description.
Titan 50 just like new. I just got done going through this entire helicopter and replacing anything that needed it. It has custom painted canopy withmetal flake windshield and checkers. (NOTE***** This canopy has been crashed and has a few flakes missing from the bottom of the canopy but otherwise in good condition see pics.) It also has carbon fiber boom supports, green paddles and a lot of spare parts. below is a list of some of the parts that is included with the Titan helicopter:
1- raptor 50 muffler
3- flybars
1-brand new belt for titan
2- sets of boom supports
2- sets of landing skid tubes
1- set of landing skids that attach to the frames
2- pushrods for the tail
1- mainshaft
1- motor mount
3- blade grips
2-vertical fins
2-horizontal fins
5- hoops
2- clutch bells
1- set of black paddles
1- elevator arm assembly
1- fan
2- tail hubs with bearings
1- ball link set
1- linkage rod set
1- output shaft
1- broken tail box however the output shaft and bearings are still good as well as the red gear on the shaft
2- futaba servo boxes FULL of spare screws, bearings, pitch links, all kinds of stuff
1- zip lock bag with lots of spare parts, screws, all kinds of stuff
I am asking $400.00 for this airframe and all the parts plus $15.00 shipping with in the US. The boom will be taken out for shipping purposes. Paypal preferred add 3%.
Now on to the second helicopter
It is a Raptor 50 V2 and has a Rickos Custom painted canopy, green paddles. This helicopter has a lot of spare parts as well. Here is a list of some of the parts.
1- raptor 50 muffler
2- flybars
5- landing gear tubes
1- set of landing gear skids that attach to the helicopter
1- set of black paddles
1- linkage rod set
2- sets of ball links
1- 10 tooth pinion
1- fin set
1- boom used but still in good condition
1- set of landing gear skid stops
5- hoops
2- new sets of tail control rod set
3- short control rods
4- long control rods
1- set of boom guides for tail control rod
1- carbon fiber rear tail servo mount to mount tail servo on the boom
3- carbon fiber pushrods for tail control
1- complete one way bearing assembly
Plus other various parts and most of the stuff to convert this to a titan push pull if wanted.
I am also asking $400.00 for this airframe and all the parts plus $15.00 shipping with in the US. The boom will be taken out for shipping purposes. Paypal preferred add 3%.
I would make someone a KILLER deal if they buy all of this. $750.00 for 2 airframes with custom canopys and all the spare parts. Plus $20.00 shipping and add 3% for paypal. Thanks for looking.
Titan 50 just like new. I just got done going through this entire helicopter and replacing anything that needed it. It has custom painted canopy withmetal flake windshield and checkers. (NOTE***** This canopy has been crashed and has a few flakes missing from the bottom of the canopy but otherwise in good condition see pics.) It also has carbon fiber boom supports, green paddles and a lot of spare parts. below is a list of some of the parts that is included with the Titan helicopter:
1- raptor 50 muffler
3- flybars
1-brand new belt for titan
2- sets of boom supports
2- sets of landing skid tubes
1- set of landing skids that attach to the frames
2- pushrods for the tail
1- mainshaft
1- motor mount
3- blade grips
2-vertical fins
2-horizontal fins
5- hoops
2- clutch bells
1- set of black paddles
1- elevator arm assembly
1- fan
2- tail hubs with bearings
1- ball link set
1- linkage rod set
1- output shaft
1- broken tail box however the output shaft and bearings are still good as well as the red gear on the shaft
2- futaba servo boxes FULL of spare screws, bearings, pitch links, all kinds of stuff
1- zip lock bag with lots of spare parts, screws, all kinds of stuff
I am asking $400.00 for this airframe and all the parts plus $15.00 shipping with in the US. The boom will be taken out for shipping purposes. Paypal preferred add 3%.
Now on to the second helicopter
It is a Raptor 50 V2 and has a Rickos Custom painted canopy, green paddles. This helicopter has a lot of spare parts as well. Here is a list of some of the parts.
1- raptor 50 muffler
2- flybars
5- landing gear tubes
1- set of landing gear skids that attach to the helicopter
1- set of black paddles
1- linkage rod set
2- sets of ball links
1- 10 tooth pinion
1- fin set
1- boom used but still in good condition
1- set of landing gear skid stops
5- hoops
2- new sets of tail control rod set
3- short control rods
4- long control rods
1- set of boom guides for tail control rod
1- carbon fiber rear tail servo mount to mount tail servo on the boom
3- carbon fiber pushrods for tail control
1- complete one way bearing assembly
Plus other various parts and most of the stuff to convert this to a titan push pull if wanted.
I am also asking $400.00 for this airframe and all the parts plus $15.00 shipping with in the US. The boom will be taken out for shipping purposes. Paypal preferred add 3%.
I would make someone a KILLER deal if they buy all of this. $750.00 for 2 airframes with custom canopys and all the spare parts. Plus $20.00 shipping and add 3% for paypal. Thanks for looking.