YGE Videos

[wicked_n_raw]

Here is the first part of the YGE videos that I have done. I will be doing more including how to set it normally and how to set it up with the vbar. I am also including a link to all the manuals and some tips documentation.

Here is the first video on the program card II.
http://www.youtube.com/watch?v=a7kbMhBaUA4

For the documents
manuals http://elektrorc.com/article_info.php?articles_id=2
Programming http://elektrorc.com/article_info.php?articles_id=5
Gov Store http://elektrorc.com/article_info.php?articles_id=6
Error Codes http://elektrorc.com/article_info.php?articles_id=7

If you think I should add something to the videos or take something out please send me a pm.

[Mystic3D]

AWESOME.

Thank You Furron

[wicked_n_raw]

You are welcome!

[fusionsx00]

Thanks:)
just in time

[joe1l]

thanks man!! very good video!

[velocity90]

Great vid wicked,

Be sure when making one for the vbar to mension that the rx channel of the program card for programing end points goes in the thr channel of the vbar, NOT channel 3 on the receiver fur futaba. I cant comment on spektrum but it goes in the vbar. Dont use the receiver anymore for programming endpoints.

Also be sure to be in "stick control over moter" mode on :D when programming the end points (stop and full speed) This is the key to making it work flawlessly.

[joe1l]

can we make this link sticky!

[jhheli]

Yea this should be a sticky, nice videos.

[wicked_n_raw]

Thank you everyone.

Here is the second video.

http://www.youtube.com/watch?v=j4lPjLZkV2g&feature=youtube_gdata

[helidude71]

Great vids!

However you recommend to go for 3.4V/cell cutoff voltage.

My own testing shows better not do this.
I've run into LVC with this setting and the charger shows 27% left in the pack.
With cut off type "slow down" there isn't enough power to even hover my bird. :face
It's clear you want to prevent LVC unneeded.

I would recommend not to go any higher than 3.2V/cell cutoff voltage.

IMHO

[laminarjack]

Thanks for the great videos. I got my HK YGE ESC programmed and will give it a test flight tomorrow. Good stuff, the instructions were crap.

[Valkman]

Many thanks mate.

[3bncbm]

Here is the first part of the YGE videos that I have done. I will be doing more including how to set it normally and how to set it up with the vbar. I am also including a link to all the manuals and some tips documentation.

Here is the first video on the program card II.
http://www.youtube.com/watch?v=a7kbMhBaUA4

For the documents
manuals http://elektrorc.com/article_info.php?articles_id=2
Programming http://elektrorc.com/article_info.php?articles_id=5
Gov Store http://elektrorc.com/article_info.php?articles_id=6
Error Codes http://elektrorc.com/article_info.php?articles_id=7

If you think I should add something to the videos or take something out please send me a pm.

This video has gone private. Any reason for this?

[K2Freak]

Yup. I'd like to watch these as well, but not allowed. :...:

[alexmit]

External Gov with YGE
http://www.youtube.com/watch?v=zbO67N-Ym0o

YGE Programming Governor Store
http://www.youtube.com/watch?v=ITCevmKW3oQ

Thanks MrMel!

[3bncbm]

External Gov with YGE
http://www.youtube.com/watch?v=zbO67N-Ym0o

YGE Programming Governor Store
http://www.youtube.com/watch?v=ITCevmKW3oQ

Thanks MrMel!

Thank you for this! Just can't understand why a "Sticky" would be private?

[wicked_n_raw]

Sorry forgot this was here!