Phoenix with DX7?

[kamtsa]

Does Phoenix work with Spektrum DX7?

Do I need to buy an adapter for DX7 or does Phoenix come out of the box with everything I need for DX7

Thanks,

Tal

[andym]

Hiya,

Phoenix works with the DX7 with the adapter supplied with the software - you don't need to buy another adapter.

Kind Regards

Andy

[kamtsa]

Hiya,

Phoenix works with the DX7 with the adapter supplied with the software - you don't need to buy another adapter.

Kind Regards

Andy

Thanks. I just ordered Phoenix.

Kam

[rabidguineapig]

Does it also work with the DX6?

[vetterick]

Yes it works with DX6 same plug (comes with Phoenix)

Rick

[andym]

oh, btw

dont forget to create a sim profile with your DX7 (copy you heli settings to a new profile, e.g. 20) and to change it to one servo, or in phoenix it all goes loopy!

Rgds

Andy

[Spectre]

oh, btw

dont forget to create a sim profile with your DX7 (copy you heli settings to a new profile, e.g. 20) and to change it to one servo, or in phoenix it all goes loopy!

Rgds

Andy
I did this and I still can not get control of the helicopter...she keeps spinning out of control.

Phoenix worked just fine on the futaba 6exh but the dx7 I am getting frustrated.

[vetterick]

You need to make sure the model for Phoenix has [SWASH TYPE] set to "1 SERVO" and "NORM", or you will need to decipher the CCPM mixing from the radio.

Rick

[Spectre]

You need to make sure the model for Phoenix has [SWASH TYPE] set to "1 SERVO" and "NORM", or you will need to decipher the CCPM mixing from the radio.

Rick

yep, This is already was done....but the heli still freaks out.

[Spectre]

Would someone be so kind as to post their DX7 settings they have for the sim.

Yes, I have it set to one servo.

I still can not get control of the tail

the Futaba 6EXH I can get to work fine but not my DX7

[Pinecone]

You still need to calibrate the sim to the Tx. If you have problems, run the calibration again, with 1.03 and earlier, it sometimes seems to loose the info.

I set up my sim heli profile to Normal, set a normal and idle up pitch and throttle curve as per Finless video (not sure why a normal since I never fly using it :) ). And I did set two expo settings to the dual rate switches for pitch and roll (no rate changes, both rates are 100%, but o and 30% expo).

Normal:
Throttle: 0 - 60 - 80 - 90 - 100
Pitch: 40 - 45 - 50 - 75 - 100

Idle Up:
Throttle 100 - 95 - 90 - 95 - 100 (or use 100 - 100 - 100 - 100 - 100)
Pitch: 0 - 25- 50 - 75 - 100

I set throttle hold to 0 with a full pitch curve for autos ( 0 - 25 - 50 - 75 - 100).

[Spectre]

You still need to calibrate the sim to the Tx. If you have problems, run the calibration again, with 1.03 and earlier, it sometimes seems to loose the info.

I set up my sim heli profile to Normal, set a normal and idle up pitch and throttle curve as per Finless video (not sure why a normal since I never fly using it :) ). And I did set two expo settings to the dual rate switches for pitch and roll (no rate changes, both rates are 100%, but o and 30% expo).

Normal:
Throttle: 0 - 60 - 80 - 90 - 100
Pitch: 40 - 45 - 50 - 75 - 100

Idle Up:
Throttle 100 - 95 - 90 - 95 - 100 (or use 100 - 100 - 100 - 100 - 100)
Pitch: 0 - 25- 50 - 75 - 100

I set throttle hold to 0 with a full pitch curve for autos ( 0 - 25 - 50 - 75 - 100).Thank you very much... I will try these

on a side note... I seem to have to recalibrate every time I start the sim... and after about 4 or 5 min of being in the sime I have to recalibrate again..and it just gets worse and worse...

wondering if I have a problem with the TX or the sim...