Post your RAZOR setup here

[j.p.75]

Akku:
Motor:
Speed Controller:
Head Speed:
Blades:
Tail Blades
Paddles:
Pitch range:
Ciclic Pitch:
Flying Time:


When you use a CC Speed Controller post here your .dat files

[j.p.75]

Akku: FP 2x 5S1P 4350mah
Motor: Kontronik Tango 45-08
Speed Controller: CCHV85
Head Speed: Normal 1750, Idle1 1850, Idle2 1950
Blades: Radix 600mm
Tail Blades: Radix 95mm
Paddles: Original Paddles
Pitch range: +11° / 0° / -11°
Ciclic Pitch: 6°
Flying Time: ~ 7 min.


When you use a CC Speed Controller post here your .dat files

################################################## #####
# Castle Link Data File
# Created: domenica 7 ottobre 2007
# Do Not Edit This File By Hand
################################################## #####
Brake Ramp: Super Slow
Cutoff Voltage: 300 <--- Why in this point more user with 10S used 180 (18v) ???
Hex55: 85
Brake Strength: 0
Direction: Forward (*)
Spool-Up Speed: 6
Throttle Type: Heli: Governor High
Current Limiting: Disabled
Brake Delay: No Delay
Motor Start Power: 2,125
Throttle Response: 2
Motor Timing: Standard Advance (*)
Cutoff Type: Soft Cutoff
PWM Rate: 13khz (*)
Governor Gain: 24,2857142857143

[PG 378]

Come on FREAKS!
We need more attention to this thread!
Here is my setup.
:thumbup:
Razor:
--------------------------------------------------------------------------------
Akku: Flight Power 25C 3700mAh
Motor:Hacker A50-14S
Speed Controller: CCHv85
Head Speed:
Blades: CY Radix 600mm
Tail Blades CY Radix 95mm
Paddles: V-Blades
Pitch range: +12.5/-12.5
Ciclic Pitch: 6°
Flying Time: 4 minutes

[bathmagic]

Akku:flight power 25c 3700mah
Motor:NEU 1515-2y
Speed Controller:CC85
Head Speed:2330 Unloaded @zero pitch
Blades:sab 620
Tail Blades92mm
Paddles:V 90mm
Pitch range:12.5
Ciclic Pitch:7
Flying Time:4-4.30 minutes of blasting fun !

I have changed my gear ratios from MA recomendations for this motor

It was a 13tooth pinion (MA recomended) i went to a 16tooth and that was orsum BUT at 100% it was nearly 2500 HS i
have now gotten from MA a 14 and a 15 tooth.
Tonight i tried the 15 and had 2330 UNloaded and 100% throttle, a quick fly produced a smile, still the puch out and SNAP but still a small vibration in the tail so i have checked alignment of the pinion on the motor and it was out a little, hopefully that was the drama.

I will try the 14 tooth and see what thats like too

I am aiming to get 2200-2300 at 0 pitch and hold 2100-2150 on the head.
That wil get it going real well but short flight times but i now have a few packs so i can fly all day.

I shall post as i do more,,,,,, even thinking about a flybarless version
i have the cylock and one 720...............................................

Dale

[buster1]

I have the same setup as PG378, except V-blades for main's - I recently just switched to the Jazz Controller, because I had a crash and attribute to either running a nicad with Spectrum DX7 (the spectrum will fail if the voltage falls below a min. required level) or the it could have been the CCHV85 controller, which I hear have had some failures.
I also like the simplicity/reliability of the Jazz even if I don't have all the features of the CC. Just got the heli. back together and looking forward to flying the Razor Again,

I was not flying it as much due to its weight, but in all sincerety it is a great quality heli. and just went back to getting it back in the air. The stability and quality is worth the extra weight,

Jeff

[TomC]

Best Razor setup imop;

Twin bladed Gillette actro+ blades and Edge advanced shaving gel for sensitive skin!

Man it's smooooth. And, it comes with a torque tube blade holder as well.

Sorry mates I could not help myself lol!

Cheers,
Tom C

[jrohland]

Akku: FlightPower EVO20 & EVO25 2x5s (10s) 4350
Motor: Kontronic Tango 45-08
Speed Controller: Kontronic Jazz 55
Ratio: 14.25/1
Head Speed: ~2000
Blades: V-Blade (600mm)
Tail Blades: Align Carbon (95mm)
Paddles: Stock
Pitch range: +11/0/-11
Cyclic Pitch: 6 (will be upped to 7 soon)
Flying Time: 8 minutes (mild pattern, flips and rolls)
Gyro: Futaba GY-611
Collective servos: Futaba 9252
Receiver power: UBEC (HV)
Radio: Spektrum DX7 (standard swash mix: see Cylock below)

Recently added:
CMS Cylock mixer
FMA Direct Copilot (CDP4) with IR sensor

See attached Eagletree graph for detailed power, battery temp(C) and RPM

As you can see using the attached graph, I could fly longer and/or harder with this setup.

jrohland

[Jeff Palmer]

Akku: FlightPower EVO's 2x5s (10s) 4350
Motor: Actro 32-3
Speed Controller: Kontronic Jazz 55
Head Speed: ~1900
Blades: V-Blade (710mm)
Tail Blades: V-Blades (105mm)
Paddles: Stock
Pitch range: +12/0/-12
Ciclic Pitch: 7.5
Flying Time: 6 minutes
Gyro: Futaba GY-601
Collective servos: Futaba 9252
Radio: 14MZ

Stretch Version

[mudbogger2]

This was the setup on mine:

Akku: 12S1P Flightpower EVO25 3300's
Motor: Actro 24-4
Speed Controller: CC HV-85
Head Speed:2150
Blades: SAB 600's
Tail Blades SAB 95's
Paddles: Stock
Pitch range: 11/11
Ciclic Pitch:7.0
Flying Time:5.5 minutes
Gyro: Logictech 6100
Cyclic servos: 9451

Flying the 9.6:1 ratio this was a very powerful setup that ran cool also.

[r2160]

Akku: 2 x 5S 3700 flightpower
Motor: Hacker A50-14s or Actro 32-3
Speed Controller: Kontronics 55-10-32
Head Speed:
Blades: TG 600mm
Tail Blades Carbontech 95mm
Paddles: Stock
Pitch range: 11-0-11
Ciclic Pitch: 8 degrees
Flying Time ?
Cyclic Servos: Futaba 9252
Gyro: GY611

Will fill in the other details later

glenn

[PG 378]

Sorry Buster to hear about your crash.
Also I totally zoned out...I said we had a Jazz 55 esc...we used to but it cut-out at around 2 mins during four flights at IRCHA...then would not come back on at all...:bawl...almost all the Mikado guys at IRCHA also had there Jaz 55's going out on them. So we now use a Castle Creations Hv85.

Paul G.
BTW: I also use a Spektrum DX7.

[Beast]

Akku:thunder power v2 extreme
Motor:hacker A50 14S
Speed Controller:Castle hv 85
Head Speed:2200
Blades: rototechs 615
Tail Blades: rotortechs 95
Paddles: mah
Pitch range:11/11
Ciclic Pitch:8/8
Flying Time:4mins



There's a vid of the machine flying 2 weekends ago at the NC event with the headspeed at 2000 in the vid section. flew this past weekend at mulberry with 2200 and it was much crisper and rock solid also make sure you keep the tail belt very tight it helps hold the tail when doing very fast backwards flight.

[t-rexn8]

Akku:thunder power v2 extreme
Motor:hacker A50 14S
Speed Controller:Castle hv 85
Head Speed:2200
Blades: rototechs 615
Tail Blades: rotortechs 95
Paddles: mah
Pitch range:11/11
Ciclic Pitch:8/8
Flying Time:4mins



also make sure you keep the tail belt very tight it helps hold the tail when doing very fast backwards flight.


Thats a nice way to mention the tail issue with the Razor. LOL. What hole are you on?
I am on the 5th hole from the front.

[Beast]

i think it's the second from the front but go by tension as all belts will stretch a bit and all will not be the same.

[t-rexn8]

Sorry I meant second from front.

[r2160]

Akku:thunder power v2 extreme
Motor:hacker A50 14S
Speed Controller:Castle hv 85
Head Speed:2200
Blades: rototechs 615
Tail Blades: rotortechs 95
Paddles: mah
Pitch range:11/11
Ciclic Pitch:8/8
Flying Time:4mins



There's a vid of the machine flying 2 weekends ago at the NC event with the headspeed at 2000 in the vid section. flew this past weekend at mulberry with 2200 and it was much crisper and rock solid also make sure you keep the tail belt very tight it helps hold the tail when doing very fast backwards flight.

Hi Beast,
can you tell us what ratio you are running on this?
thanks
Glenn

[busted blade]

razor # 1
tp3850's 10s
hacker a50-14s / 9.0:1
2080hs @hover and 100% throttle
jazz 55-10-32
swe 620mm mains
95mm v-paddles
95mm radix or v tails
+- 11deg pitch and acceleration to +-14 for about .25 seconds
9deg cyclic
metal grips, mix arms, and washout arms
long balls on swash inner ring for bell input
4:45 burns about 2800 mah
14mz, 9252's, 611 gyro
Razor # 2
same as # 1 but with neu 1515 2y / 18.46:1 and evolution 620mm mains

both weight about 8.5lbs RTF and both fly about the same but the neu motor has a little more grunt
gonna try v-stabi flybarless next

[Chachin]

Hello, here is my current Razor setup:

Akku: 10S TP 3850 Extreme V2
Motor: Kontronik Tango45-06
Speed Controller: Kontronik Jazz 55-10-32
Head Speed: 2200rpms (unloaded)
Blades: 600mm v-blades TST Edition
Tail Blades: 95mm v-blades
Paddles: Stock White 3D paddles
Pitch range: +/- 10.5
Cyclic Pitch: +/- 7.5
Flying Time: 4.5min so far with plenty of reserve
Gyro: GY-502 with 9254 tail servo
Servos: S9252 Digitals

Video from Port Charlotte funfly:
http://www.rcgroups.com/forums/showatt.php?attachmentid=1718270

Will post again after some changes are made.

Chachin..

[PG 378]

Hi Beast,
can you tell us what ratio you are running on this?
thanks
Glenn

I'm not Beast...but...I have a 8.72:1