Help - Setup Help Please for Logo 500 3D

[rcscrewz]

Been flying nitro for years - want to get in the electric realm. Just purchased a Mikdao 500 3D and am using a futaba 601 gyro with 94256 tail servo and 251's servos. But I have no Idea what to use for A Speedo, motor and batttery - money is no object - I want the best setup for 3D flying

[LITHIUMSTATIC]

Kontronik Jazz 55-10-32

FlightPower EVO25 6s 5000

Not sure what motor would be the best for that heli.

EDIT*** A NEU 1910(H)-1Y or a Tango 45-10...... I think the NEU would be better for throwing the heli around.

[OICU812]

Motors:

So far here is the gig, in no order and these so far have all been excellent choices.

NEU 1910(H)-1Y // 16T mod.7
ZPower Z30A-1100 // 16T mod.7
ZPower Z50A-1150kv // 16T mod.7, would opt 15T perhaps next round
Hacker A40-10L 1100kv// 16T mod.7
Hacker A40-8L 1300kv// 13T mod.7
Tango 45-10 // 16T mod.7

Now if you are going to stick with 6S, than go with the Kontronik Jazz 80-6-18 esc, that will be the best bar none for 6S L5003D. Cheers. :smokin:

Oh... and run 550 mm main blades, and no larger than 92mm tr blades.

[BruceW]

I notice that the 0.7 mod gears are getting pushed here mostly. Are they tougher than the 0.5 mod gear with less stripping?

[Eyon]

yes they just have deeper cut teeth. Both m05 and m07 come with the 3D kits now (not the DX)

My personal recommendation, as its what i fly, is the Hacker A40-8L 8Pole with a 15T mod07 gear on 550 blades. 2350rpm. running K&B tails for 50 sized. this gives more power than i could ever want, its just awesome fun to fly. I used to run 500mm, but i dont think ill go back, 92 tails give great tail authority, but i dont mind having a little less power on the tail with so much more power on the head

I think i have got some sub-10g paddles on it too, its great fun, turns on itself.

[Foamy Love]

Enyon,

Where are you seeing the 2350 headspeed at throttle position wise?

[OICU812]

yes they just have deeper cut teeth. Both m05 and m07 come with the 3D kits now (not the DX)

My personal recommendation, as its what i fly, is the Hacker A40-8L 8Pole with a 15T mod07 gear on 550 blades. 2350rpm. running K&B tails for 50 sized. this gives more power than i could ever want, its just awesome fun to fly. I used to run 500mm, but i dont think ill go back, 92 tails give great tail authority, but i dont mind having a little less power on the tail with so much more power on the head

I think i have got some sub-10g paddles on it too, its great fun, turns on itself.


15tooth @ 1300kv?? WOW!
RPM at low load: 2790 at 22,8 volt RPM at medium load: 2606 at 20,64 volt RPM at full load: 2423 at 19,8 volt

[Eyon]

fixed end point mode of the CC85, 0 degrees pitch, 85% throttle.

Shawn, doesnt quite work like that, remember motors are only about ??85% efficient, gear train isnt 100% efficient either, and im turning 550mm blades, with a flybar. I think the extra drag just works it. i spent a lot of time getting my heli set up as i like, think i tried 4 different mod07 pinions before i found i liked the 15. Its no doubt a set up issue, but it works for me, so whos to complain!!!

[Foamy Love]

Okay I'll start with the 13t with the V-Bar and go from there.

[OICU812]

Ok Ian, just seemed like a super high number was all. If it works rock on man! :smokin: