jaywhy
11-24-2007, 08:03 PM
Mint condition Align Trex SE V2 (all metal head/tail/carbon fiber frame and fins) - assembled, test flown once, less than 10 seconds air time! After putting the money and time in (my 1st bird), I realized I couldn't handle seeing this beauty wrecked by a newb like me - so I got a 450x and have flown/upgraded that since. I was hoping I could hold on to the V2 until I was ready for it - but I'm basically getting layed off a month before Christmas. Isn't that swell! :(
Assembled 450SE V2 (real deal), Futaba GY401, Futaba 9650 on tail, *2* Hitec HS65mgs, AR7000 RX
Does not include: the Align battery (guess why?), Align carry case, DX7 controller (if you don't want to use a DX7 for this bird, I'll take another $75 off the price and remove the installed AR7000 receiver.)
Also: Needs 1 65mg to complete other 2 in cyclic (removed one for my crash and learn bird - this V2 for sale has NEVER wrecked.)
I also have added blue Medusa wrap-a-around heat sink on the 430xl ($6.50 value) already attached with artic silver. Gorilla landing gear! (orignal, full set with skids also included.) Faux carbon fiber paddles (originals included), set of Align tools (screw-drivers and hex wrenches), `Screw Parts` bag of extra screws and things. (Parts bag was opened, only a screw or two taken out.) To the best of my knowledge (sorry, bad memory), but I'm pretty sure the tail fins are the Gorilla tail fins. I'll also include the Align pro 315 blades that are on the bird in the picture. ($13) Also, Align pitch guage, a set of male and female deans connectors, and swash leveler.
I added a sturdier tail servo control arm rather than the flimsy wire included with kit. Much better, it's just like what I use on the bird I fly.
This 450SE v2 has been in the air for less than 10 seconds! Only wear is slight scuff on bottom of landing gear from reversed gyro when I first tested. That, and a little bit of dust from sitting on the shelf. :(
She is MINT, never crashed or even tipped over on a spool up, with the original V2 canopy and the original carbon fiber blades, manual. I can even send the original box it came in if you want!
If you want a basic Align lipo balance/charger:
http://www.google.com/products?q=align+charger+balancer+3cx&show=dd
I can include this one for $30 - I paid $40. I still want it for a second charger, but I've got a BC6 for a primary and I need the money more than a second charger. :( Charger has been used no more than three times.
$700 + $15 for shipping
$625 + $15 if you don't want the AR7000
(PM me if you want to make an offer - I might be swayed as time runs out.)
Paypal only - or local pick-up, cash only (minus shiping), I'm a couple miles away from Discount Hobby Warehouse (in no way affiliated) in San Diego, California.
I've got really good foam to pad up (in picture, it looks yellow and old but I bought if for my bird's carry case
and have plenty. The tail/boom will most likely have to be taken off, but she'll be shipped with loving care.
Assembled 450SE V2 (real deal), Futaba GY401, Futaba 9650 on tail, *2* Hitec HS65mgs, AR7000 RX
Does not include: the Align battery (guess why?), Align carry case, DX7 controller (if you don't want to use a DX7 for this bird, I'll take another $75 off the price and remove the installed AR7000 receiver.)
Also: Needs 1 65mg to complete other 2 in cyclic (removed one for my crash and learn bird - this V2 for sale has NEVER wrecked.)
I also have added blue Medusa wrap-a-around heat sink on the 430xl ($6.50 value) already attached with artic silver. Gorilla landing gear! (orignal, full set with skids also included.) Faux carbon fiber paddles (originals included), set of Align tools (screw-drivers and hex wrenches), `Screw Parts` bag of extra screws and things. (Parts bag was opened, only a screw or two taken out.) To the best of my knowledge (sorry, bad memory), but I'm pretty sure the tail fins are the Gorilla tail fins. I'll also include the Align pro 315 blades that are on the bird in the picture. ($13) Also, Align pitch guage, a set of male and female deans connectors, and swash leveler.
I added a sturdier tail servo control arm rather than the flimsy wire included with kit. Much better, it's just like what I use on the bird I fly.
This 450SE v2 has been in the air for less than 10 seconds! Only wear is slight scuff on bottom of landing gear from reversed gyro when I first tested. That, and a little bit of dust from sitting on the shelf. :(
She is MINT, never crashed or even tipped over on a spool up, with the original V2 canopy and the original carbon fiber blades, manual. I can even send the original box it came in if you want!
If you want a basic Align lipo balance/charger:
http://www.google.com/products?q=align+charger+balancer+3cx&show=dd
I can include this one for $30 - I paid $40. I still want it for a second charger, but I've got a BC6 for a primary and I need the money more than a second charger. :( Charger has been used no more than three times.
$700 + $15 for shipping
$625 + $15 if you don't want the AR7000
(PM me if you want to make an offer - I might be swayed as time runs out.)
Paypal only - or local pick-up, cash only (minus shiping), I'm a couple miles away from Discount Hobby Warehouse (in no way affiliated) in San Diego, California.
I've got really good foam to pad up (in picture, it looks yellow and old but I bought if for my bird's carry case
and have plenty. The tail/boom will most likely have to be taken off, but she'll be shipped with loving care.