Share your Logo V-Stabi files here!!!

[OICU812]

Well with the growing popularity of the V-Stabr, aka: Vbar it seems necessary to have a section where we can all share our files and settings.

Now rather than just sharing the file itself I find it cruicial we also share what our radio settings are, and of course what hardware are we running on our heli, ie: servos and motors.

If you like you can also share any comments to your setup. Lets please make this as descriptive and exact as possible to better help people new to the V-Stabi and the Logos.

In the end we will all gain knowledge from this and most likley all have much better flying Logos equipped with V-Stabi

[Flybar-less]

Xml allowed?

[OICU812]

Ok here is a template that we can all use in our responses, simply copy and paste then insert your data and of course attach file. I feel this will greatly help the user prior to selection of a file. As always folks ***REMEMBER*** only import the files you wish to use, and ensure correct operation of the swash movement and tail operation before flight. It is highly suggested you have your working file saved and your servo directions and trims written down "minimum" PRIOR to loading in someone elses file.

The items listed below I feel from all the reading and conversations are the most important and make the largest differences in flight characteristics. If you feel there should be abit more we can certainly modify this "PM me", but it would be nice to keep it as simple and to the point as possible. Also please uplaod your **Favourtie WORKING file**.


Here we go:

Setup is for 3D, FAI, Scale?:
Main Blades "Brand and size":
Tail Blades "Brand and size":
Headspeed:

Transmitter used:
Cyclic Servos:
TR Servo:
Endpoints for Aileron:
Endpoints for Elevator:
Endpoints for Tail Rotor:
Ail Expo:
Ele Expo:
TR Expo:

Lipo Used:

General comments from user:

[OICU812]

Xml allowed?


Just upload it as you did the last John. From that you can open it with the Vbar software easily.

[Flybar-less]

My latest files.
Since Vstabi only saves 1 bank of info per file I have posted 2 files.
The first (B1) is cyclic version of DJ's, works well in windy conditions.
The second (B3) is a cyclic version of MB's, this is my favorite.

Main blades: Maniac 623 or SAB 620
Tail parameters are for JR 8900G and CY 95s
RPM 2,300
TX 100% Expo 15%
12 degrees collective, 8 degrees cyclic
AOF 7/60
IC sensor set

Heli: Logo 600 3D, Neu 1912H/1Y, 13T, JR 8717s on cyclic, JR 8900G on tail w/Emcotec 5.2V regulator, JR 921 RX, Power Jazz with diode 0.7 volt drop on throttle input, 2S 1350 RX pack w/ 2 HD leads, Maniac 623 blades, CY 95 tail blades, FP 4350 10S & 5350 10S.

rename file extension .xml

[uragano47812]

The setup from vstabi CD for L500 is a good point to start?

I have already setup mine in classic mode, but not fly it yet.
Uli said to me to import cyclic and tail parameters from a preset, will the one from CD be good?

Thanks

[OICU812]

The setup from vstabi CD for L500 is a good point to start?

I have already setup mine in classic mode, but not fly it yet.
Uli said to me to import cyclic and tail parameters from a preset, will the one from CD be good?

Thanks


Yes it will be fine, you will need of course to do your own subtrim as per your servos and horns as well your own tail rotor travel limits etc, lets please keep this thread for the files not the questions, thanks.

[Taipan]

Where do I find Danny J's latest file?

[Flybar-less]

Logo 600 mechanics, 500 canopy, 690mm carbon boom, 8S FP 5350 long/FP 4900 long, Neu 1910H/1Y, 17T mod .5, CC 85HV, CC BEC 5.1V on tail servo, FP 2S 1350 RX pack, 8717s, 8900G, Radix 600s & 95s, 9 degrees cyclic, 13 degrees collective.

[OICU812]

Logo 600 mechanics, 500 canopy, 690mm carbon boom, 8S FP 5350 long/FP 4900 long, Neu 1910H/1Y, 17T mod .5, CC 85HV, CC BEC 5.1V on tail servo, FP 2S 1350 RX pack, 8717s, 8900G, Radix 600s & 95s, 9 degrees cyclic, 13 degrees collective.


WOW cool man! I like how you actually got the 599 on the decal! That looks great man. :smokin: On a side note I do not currnetly have any "tweaked" files to share as other then a trim flight here and there I have not been able to fly because of a bad winter. Once I do I certainly will share any and all files I get as this in the end is about everyone enjoying the technology and I praise those who are so willing to support the community, thank you.


**BTW** Note to future file users and people leaving files. When saving your file remember it does not save all banks to one file, only the bank you are on at the time of saving. You have to save each individual bank to computer.

[Flybar-less]

Logo 600 3D with 500 canopy, 17 tooth mod.5 gears w/ counterbearing, 8S FP 5350, Radix 600s, 686XL neoprene belt, 690mm carbon boom, 95mm Vblades, CC HV85, Neu 1910H/1Y, JR 921, 8717s, 2S FP 1350, CC BEC 5.1V to 8900G on tail.

2300 headspead
7 minute runtime

[Flybar-less]

The Logo 599 really flys well the the CY Radix 600 "stick bangers" 121gram blades, same setup. Excellent for both 3D and FFF manuevers.

[OICU812]

The Logo 599 really flys well the the CY Radix 600 "stick bangers" 121gram blades, same setup. Excellent for both 3D and FFF manuevers.


I had heard the SB version would be to light as their CG is inward... So no weird tendacies with the SBs' at all?

Hmmm I have a set of those, was going to put them on the flybar unit and run the regulars on my Vstabi one...

[Adam Turner]

Adam's Setup:

Mikado Logo 600 3D-Vbar Head. X2
Main:620mm V-blades
Tails: 110mm V-tails
Battery: 10S1P 3700 Evo25
10S1P 4350 Evo 25
Tx: DX7
Rx: AR6200
Servos: Futaba S9351 x3
Tail Servo: S9256
Rx pack: EvoLite 2100 2s (10 flights per charge)
Regulator: Fromco switching
Motor: Orbit 30-12
ESC: Jazz 55-10-32
Pinion: 15T
Main Gear: 153T
V-Bar
Vbar setup:
Stability: 120
Elevator Cyclic Speed: 6
Elevator stop Behave: 37

Aileron Cyclic Speed: 0
Aileron stop Behave: 35

Speed mixer: 4
Speed Limiter:0

Tail Torque Comp:
Cyclic: 15
Collective: 25
Sensitivity: 66
Symmetry: 15

Stick Acceleration: 80
Proportional Gain: 90
Integrator:35
Differentiator:0

Collective 72
Bell: 20
Hiller: 95

Cyclic ring: 60

Jazz ESC: setting 4. Heli Gov mode.

Spectrum DX7 Program: (anything I have not mentioned is left as defult)
Heli Mode normal: Not CCPM V-bar automatically does this.
D/R:100%
EXP: +20%
Reverse: Ch 2, 4
Throttle hold pos: -5%
Throttle Curve:
Point 1,2,3,4,5
Normal 0%, 0%, 0%, 0%, 0%, 0%
Idle Up(ST-1): 80%, 80%, 80%, 80%, 80%
Idle Up(ST-2):60%, 60%, 60%, 60%, 60%,
Pitch Curve: (all)
0%, INH, 50%, INH, 100%

Hope this helps!!

[flypilot]

Here is my Trex500 vbar setup:

http://www.helifreak.com/showpost.php?p=530293&postcount=16

[Flybar-less]

I finally have this set up the way I like it. The futaba BLS251 works excellent with Vstabi. I pre-treated the stock PU 730XL belt and guide pullies with Graphit 33.

Logo 600 3D
FP 5350 10S
Neu 1912H/1Y w/ 13T mod .7 and counterbearing
Fp 1345 2S RX (2 leads to RX)
JR 921 w/ Spektrum logger
JR 8717s
BLS251 w/ Emcotec 5.2V regulator
Maniac 623s
Radix 95s
Quick UK tail grips (5mm larger disc)
Raptor 90 CF boom

2,300 headspeed
7+ minutes flight time

[Flybar-less]

This file has been used for many months and flown by numerous pilots whose skills are between advanced to pro. It is important to recognize that the setup is for for a 10S Logo 600 3D with JR8717s on cyclic and a Futaba BLS251 tail servo, and probably will not work well with a different configuration. The file has an extended mode edit for this heli, which can only be transfered by uploading this file. This is not a beginner file!

Specifics;
Radio: JR 9303 or Spektrum DX7
100% ATVs
25% Expo
Aileron reversed
Trim disabled
Reciever: JR921 2S power
Battery: FP 1345 RX
Servos: JR 8717s w/ Mikado arms 2S power
Tail Servo: Futaba BLS251 w/ 5.2 voltage regulator and 13.5mm Futaba arm

Blades;
Main: Radix 600 and Radix 600 "SB"s, Maniac 623s, SAB 620s
Tail Blades: Radix 95s and Vblade 95s
2 washers per side on head

Motors: Neu 1912H/1y, Plettenberg Heli Expert 30-12
ESCs: CC 85HV, CC 110HV, Kontronik PowerJazz, Schulze 32-80
Batteries: FP 4350 and 5350 10S
2,300-2,400 headspeed

Suggested Vstabi edits;
Expert Aileron and Elevator: Proportional 70-90% ( This is like stick direct )
Servo: Common Collective- increase or reduce 5% for approx 1% collective pitch change.
Fit Paras: Elevator and Aileron stop behavior- increase 5% for 620s, decrease 5-10% for 600s and/or lighter batteries
Expert Swash: Cyclic Gain increase 5-10% for faster roll and flip rate
Collective Pump 30-60% if you like this
Expert Rudder: D Gain 25-15% defines stop behavior
Stick Gain: increase for faster piro rate
Collective and Cyclic Comps- +- 3%
Rudder: Sensitivity 75%-125% depending on how smooth your tail linkages are?

[gtrick90]

Here my Flybarless Protos 500 setup:

MSH Protos 500 with custom made swash-driver

Main: 425mm stock SAB blades
Tails: 68mm Robbe Eolo tail blades
Battery: 6S1P 2170/2500 Evo25
Tx: JR x9303 2.4Ghz DSM2
Rx: AR6100
Servos: Futaba S9650 x3
Tail Servo: S9257
BEC: KoolFlight UBEC HV
Motor: Lipotech stock
ESC: Jazz 55-10-32
Pinion: 15T

JR x9303 2.4GHz DSM2 Program:

Heli Mode
SWASH TYPE = 1 Servo NORM
D/R:
Rudder 100% EXP +25%
Aileron 100% EXP +20%
Elevator 100% EXP +20%

Reverse: Ch 2, 3, 4

Throttle hold pos: 0%

Throttle Curve:
Point 1,2,3,4,5
Normal 0%, 50%, 50%, 50%, 50%, 50%
Idle Up(ST-1): 65%, 65%, 65%, 65%, 65%
Idle Up(ST-2):85%, 85%, 85%, 85%, 85%,

Pitch Curve: (all)
0%, INH, 50%, INH, 100%

Enjoy!!

[Flybar-less]

Tighter tail settings, faster cyclic, more stability.

[realestateguru]

These are my original files: