POST your 14MZ & 12Z Setups, Pictures, and Sound Files H

[EricLarson]

This is the place to post your 14MZ, FX-40 & 12Z files. Please share them, as we all can learn from one another.

[EricLarson]

This is a basic ECCPM Model setup. The reversing and servo layout is set for Miniature Aircraft Helicopters.

This setup uses a GV-1 governor set to "off" in normal, and 1750 in idle up 1&2. Also it is set up for the GY601 gyro in AVCS mode at 38%. Switch E is condition (Idle, 1, 2) switch F is governor off override, switch G is throttle hold, Switch H is throttle cut when the throttle stick is at idle.

The setup is very simple and a good base point to work off of.

[Racer38]

Thanks Eric

I just got my 14MZ today. I have a Spectra with 601 and GV1 I'll let ya know how close it is on the spectra and if I need to make any changes I'll post them.

Also have you noticed that the throtlr stick doesnt appear to go full travel ?? Mine doesnt go all the way to the last white index mark.

[EricLarson]

The throttle stick travel is reduced in both the 14MZ as was the 9Z. You notice it because the lines do not line up, but they are the same travel. It took me a while to get use to it as the 9C has full travel. Don't ask me why they did that, it is just the way it is. If you want full travel, you need to send it to Hobbico and have them remove the limiters and recalibrate it. I still may do that, I just do not have the time now. I really can not say if I like it reduced or not, it is just different.

Ya let me know if there is anything messed up in there! I think that setup is pretty decent, but for some reason we loaded up one and the gov was reversed, but worked in my radio fine... not sure what happened there.

Good luck and let me know how it is going!

[sapca]

Program for DYNA - X with YS 91 and 1:8 gearing
GY601 @ 38 % on sw F on and off @ normal 50%
TJ PRO : off @ normal curve expo
on 1760 @ idle 1 V-curve
on 1850 @ idle 2 V-curve
together on idle sw C
Trottle hold @ sw G
Trottle cut @ sw H

Expo aileron -30% D/R 80 %
elevator -30% D/R 80 %
ruder -20% D/R 100%

Channels:
1 aileron
2 elevator
3 Trotle
4 ruder
5 gyro
6 governor
7 pitch

Best regargs
Sapca

[Racer38]

Here is my Spectra G Picture, This Radio is soooo Cooool :lol:

[manuelg]

Is anybody out there with a raptor setup?

Manuel :?: :dontknow

[EricLarson]

I could easily mod my setup just a bit and get it right for standard mix. The rest of the setup will be the same. I will see about doing that tonight or tomorrow.

later,

[d_wheel]

Is anybody out there with a raptor setup?

Manuel :?: :dontknow

Manuel, here is the setup and picture for my Raptor 50. I am using an OS 46; 9252 servos; GY501 with 9254; Futaba governor with 1750 rpm in normal, 1850 in idleup 1, and 1950 in idleup 2; Thundertiger CF blades, +/- 9 degrees pitch in normal and idleups, -5 to +14 in hold; stock tail blades.

Later;

D.W.

[rcman]

Eric,
By chance do you have your Ion-X model that we could download :)
I know it is very close to the same as the fury one you done but the Throttle curves and we don't need the Gov part
David

[EricLarson]

Sure, when I am home later I will post it up.

[rcman]

Thanks Eric
Your the man

[manuelg]

D_Wheel,

Thanks a lot.

Does anybody have sound bits files?

Manuel

[Ensonic]

Hi,

hope someone finds them helpful :D incl. any kind of flight mode, Gov On / OFF, Idle Cut, Idle Low, Hold, Autorot Idle / Autorot Cut etc...

[WillJames]

Here are my contributions so far.

Reflex Sport 90 Setup
Ion-X Single Stage Actro 32-3 77-O-H
Ion-X Dual Stage NEU 1521 77-O-H
TREX CCPM NEU 1107 Jazz ESC
Lark 3D Plank 4 mode pretty cool

Plus a few of Shannon's Models...

You guys have nay models you want to share? Lets build up some starting points for people getting the KILLER 14MZ! Thanks in advance for sharing!!

[iachia]

These are my files for the 3D MP, Avant EFX and Hirobo Mini Lama.
Please note that all of them are in mode 1.
- The Avant is setup for the Gy611 and TJ Rev Max so idle up 1&2 have a straight 100% throttle curve.
- the 3D MP is setup for the CSM 720.
Both of them are setup for 0° at center stick and have a linear pitch curve.
The difference beethween idl up 1&2 is that in idle 2 you have a slower tail.
bye
Iacopo

[Mille aka Fredrik]

Any more sounds out there?

[sagres1]

hello everybody
does anyone has a setup program ( file mdl) for 14mz, program to work with a vario bell222/230 or airwolf...

thanks

[Rossta RAT]

Hello All
Anyone have a 3d Setup for a Century Preditor??????
Thanks
Ross

[Rossta RAT]

Anyone have something that would work, or a program that I can mod for the Pred?
Thanks
Ross

[pilotError]

The JK ECCPM model would be a good start. I think it has GV-1, GY601, and pretty much all the conditions setup.

You would probably need to change servo reverse where applicable and the swash settings (I don't have a predator - don't know if its CCPM or not).

That would get you going pretty far, as would any of the models listed above. 90% of the programming is the same between helis for a basic setup.

Mike...

[Rossta RAT]

Thanks Mike :glasses2:
New to Set-ups! :arggg: I will start there!
Thanks Again! :noteworthy
Ross

[rfaster]

Any TREX SE450 "Stock" setup?

[WillJames]

Any TREX SE450 "Stock" setup?


I ahve a few TREX models I will try to upload later today after I get a few more videos out. I think one of them is Charles Rosario's Stock CDE setup.

[jambo]

Here is my Stratus setups that I use for both, I have included both my pictures.

Also included is a reflex xtr bmp

My setup is :-

GY611 + 9256
servos 9255 all round
+10 to -10 on all modes
+10 to -6 on throttle hold (on switch g)
revlock with set at 1700, 1850 & 1900 (on switch e)
revlock off (override on switch d)
throttle cut on switch h