Speed stick 3D
01-04-2008, 04:39 AM
I have a Swift 16 that has about 100 flights on it.. Still flying great.. Only Been Crashed once and all it did was break the tail.. The tail for a T-Rex 600 was Modified to fit on the swift boom and the boom was cut 1 half inch.. It works great and i think it is better than the stock one bacause it is more rigid...This Heli used to be flybarless and all is stock now except for the tail and landing skids..Here is the setup...
Swift 16
Upgrade Metal Head Block
2 Spare Plastic Blade Grips with Bearings
Century Outrunner 600 + Motor
Align 75 Amp Esc
Thunder Power 3850 5 Cell Li-PO 100 Cycles
3 Futaba 3151's On cyclic
Maxwell 831 Mg .08 @ 6.0 V .10 @ 4.8 V
Futaba GY 401
Hitec II8 S reciver (auto shift)
Deans 2 Peice
Hitec Ch 23 Crystal
Sanyo 1200 mAh 4 cell 2 P (used two reciver packs and made it one in parellel)
T-Rex 600 Tail
Raptor 60 Tail Grips and Hub
Raptor 30 Tail Blades
T-Rex 600 Landing Gear set
Helimax 530 mm CF Blades
The Thunderpower batt was crashed and given to me.. I took it down to the local Thunderpower warehouse and they put a new cell in and repaired it but there are no balance taps on it.. Charges up to 21.00 Volts every charge still and gives me a 6-7 min 3D flight running 100 % TC....
I also have a Kyosho Caliber 400 That has the following setup..Only 10 Flights on it..It has CF frames.. Pretty nice...Kyosho has a bad head design and it is really sloppy...
Kyosho Caliber 400 CF
Stock Brushed Motor
EF 20 Amp Brshed Heli esc (with soft start)
Align 315 woddies
PollyQuest 2200 25 C 3 Cell li-po (150 cycles) from my old slow stick
3 Hs 55's on cyclic
1 HS 55 on Tail
Telebe Micro Heading Lock Gyro
Electron 6 Reciver (Hitec or Futaba)
CH 38 Crystal
Both these helis are RTF all they need is a Charger and a Transmitter and bamm!!!! They both are nice flying helis but i want to get a nitro 50....
Price for Swift With everything listed (700.00) Plus shipping
Price for Caliber 400 CF with everything Listed (350.00) Plus shipping
If you are interested in both 1050.00 and ill pay shipping I will trade everything listed above for a 50 Nitro 3D Heli.. I am looking for a Raptor 50 titan or Se v2.. maybe even a nice RTF T-rxe 450 SE V2....
Lokking for
Raptor 50 titan or better
3 Cyclic Servos (digital) Futaba 9202's or better
Gyro 401 or better
Futaba 9254 tail servo or better
Mussle Pipe 5 50 size
OS 50 Hyper
Futaba GV-1 or better
A reciver battery
Switch Harness
600 mm CF blades
A reciver - or + shift any channel
Pretty much looking for a RTF 50 size or bigger nitro 3D heli for trade or will sell for price listed above.. Ill get pictures hopefully tomorrow becuase family memeber took my digital camera on trip...
Anyways thanks for looking
Speed stick 3D :D
Swift 16
Upgrade Metal Head Block
2 Spare Plastic Blade Grips with Bearings
Century Outrunner 600 + Motor
Align 75 Amp Esc
Thunder Power 3850 5 Cell Li-PO 100 Cycles
3 Futaba 3151's On cyclic
Maxwell 831 Mg .08 @ 6.0 V .10 @ 4.8 V
Futaba GY 401
Hitec II8 S reciver (auto shift)
Deans 2 Peice
Hitec Ch 23 Crystal
Sanyo 1200 mAh 4 cell 2 P (used two reciver packs and made it one in parellel)
T-Rex 600 Tail
Raptor 60 Tail Grips and Hub
Raptor 30 Tail Blades
T-Rex 600 Landing Gear set
Helimax 530 mm CF Blades
The Thunderpower batt was crashed and given to me.. I took it down to the local Thunderpower warehouse and they put a new cell in and repaired it but there are no balance taps on it.. Charges up to 21.00 Volts every charge still and gives me a 6-7 min 3D flight running 100 % TC....
I also have a Kyosho Caliber 400 That has the following setup..Only 10 Flights on it..It has CF frames.. Pretty nice...Kyosho has a bad head design and it is really sloppy...
Kyosho Caliber 400 CF
Stock Brushed Motor
EF 20 Amp Brshed Heli esc (with soft start)
Align 315 woddies
PollyQuest 2200 25 C 3 Cell li-po (150 cycles) from my old slow stick
3 Hs 55's on cyclic
1 HS 55 on Tail
Telebe Micro Heading Lock Gyro
Electron 6 Reciver (Hitec or Futaba)
CH 38 Crystal
Both these helis are RTF all they need is a Charger and a Transmitter and bamm!!!! They both are nice flying helis but i want to get a nitro 50....
Price for Swift With everything listed (700.00) Plus shipping
Price for Caliber 400 CF with everything Listed (350.00) Plus shipping
If you are interested in both 1050.00 and ill pay shipping I will trade everything listed above for a 50 Nitro 3D Heli.. I am looking for a Raptor 50 titan or Se v2.. maybe even a nice RTF T-rxe 450 SE V2....
Lokking for
Raptor 50 titan or better
3 Cyclic Servos (digital) Futaba 9202's or better
Gyro 401 or better
Futaba 9254 tail servo or better
Mussle Pipe 5 50 size
OS 50 Hyper
Futaba GV-1 or better
A reciver battery
Switch Harness
600 mm CF blades
A reciver - or + shift any channel
Pretty much looking for a RTF 50 size or bigger nitro 3D heli for trade or will sell for price listed above.. Ill get pictures hopefully tomorrow becuase family memeber took my digital camera on trip...
Anyways thanks for looking
Speed stick 3D :D