Baron
01-04-2008, 07:45 PM
I’m selling my Miniature Aircraft Fury Extreme helicopter with OS 91 C-Spec PS engine and CY Muscle Pipe 2. Has approximately 8-10 gallons of CP 30% through it, with mostly hovering and some smooth forward flight maneuvers, no 3D at all. Engine runs good, was always run rich. It has a 3-needle carb and has never experienced any of the reported leaning in midrange. I’m selling this heli because I’m going all electric.
It comes with 2 sets of spare G10 frames, including both 8.45 and 8.18:1 plates for each (this heli has 8.18:1 for the OS). The canopy has custom Callie Graphics (orange/blue/black). The additional graphics that came with the custom scheme (Fury logo, Hitec,Futaba, JR logos, additional black trim) and the original MA decal sheet are included. The original manuals for the heli, engine, and muffler are included. A heavy-duty JR charge switch is mounted (just with double-sided tape) for access without having to cut the canopy. The canopy has no holes cut in it.
NHP 105mm carbon fiber TR blades are included. It is plumbed for a header tank mounted on the left rear of the frame. I ended up putting the header tank on a different heli, but I have a brand new KSJ header tank that is included. Black KSJ skid stops are also included. Unfortunately, I don’t have the horizontal fin. Some spare parts that I have for this heli are TR grips, TR pitch slider, TR shaft, and TR thrust bearing (See all the spare parts in the picture). I have a longer-than-stock flybar on it. The original flybar is a little bit bent when rolling on a countertop, but if you would want to try to straighten it, I’ll include it (it’s the flybar in the picture of the spare parts).
Some upgrades I did to this heli… 3-needle carb on engine, open TR gearbox, new stronger TR hub, newer torque tube with pinned ends, molded dampers (original O-rings included as well), newer harder clutch dampers (originals included as well).
I’ve got some fresh fuel tubing and new OS #8 and A3 glow plugs if the buyer needs them.
Summary:
Miniature Aircraft Fury Extreme
OS 91 C-Spec PS (w/ 3-needle carb)
CY Muscle Pipe 2
NHP 105mm TR blades
Original 3D paddles
JR heavy duty charge switch
KSJ Header Tank
KSJ Skid Stops
Upgrades:
Open TR Gearbox
Stronger TR Hub
New Torque Tube w/ Pinned Ends
Molded Dampers
Harder Clutch Dampers
Spare Parts:
(2) G10 frame sets (each with 8.45 and 8.18 plates)
TR Blade Grips
TR Shaft
TR Pitch Slider
TR Thrust Bearing
Snap-On Retainer Pitch Plates
2mm Hex Nuts
Original O-ring Dampers
Original Clutch Dampers
$850 shipped & insured to lower 48. Paypal accepted if buyer covers 3% fees.
Feel free to PM me with any questions.
-Baron Johnson
It comes with 2 sets of spare G10 frames, including both 8.45 and 8.18:1 plates for each (this heli has 8.18:1 for the OS). The canopy has custom Callie Graphics (orange/blue/black). The additional graphics that came with the custom scheme (Fury logo, Hitec,Futaba, JR logos, additional black trim) and the original MA decal sheet are included. The original manuals for the heli, engine, and muffler are included. A heavy-duty JR charge switch is mounted (just with double-sided tape) for access without having to cut the canopy. The canopy has no holes cut in it.
NHP 105mm carbon fiber TR blades are included. It is plumbed for a header tank mounted on the left rear of the frame. I ended up putting the header tank on a different heli, but I have a brand new KSJ header tank that is included. Black KSJ skid stops are also included. Unfortunately, I don’t have the horizontal fin. Some spare parts that I have for this heli are TR grips, TR pitch slider, TR shaft, and TR thrust bearing (See all the spare parts in the picture). I have a longer-than-stock flybar on it. The original flybar is a little bit bent when rolling on a countertop, but if you would want to try to straighten it, I’ll include it (it’s the flybar in the picture of the spare parts).
Some upgrades I did to this heli… 3-needle carb on engine, open TR gearbox, new stronger TR hub, newer torque tube with pinned ends, molded dampers (original O-rings included as well), newer harder clutch dampers (originals included as well).
I’ve got some fresh fuel tubing and new OS #8 and A3 glow plugs if the buyer needs them.
Summary:
Miniature Aircraft Fury Extreme
OS 91 C-Spec PS (w/ 3-needle carb)
CY Muscle Pipe 2
NHP 105mm TR blades
Original 3D paddles
JR heavy duty charge switch
KSJ Header Tank
KSJ Skid Stops
Upgrades:
Open TR Gearbox
Stronger TR Hub
New Torque Tube w/ Pinned Ends
Molded Dampers
Harder Clutch Dampers
Spare Parts:
(2) G10 frame sets (each with 8.45 and 8.18 plates)
TR Blade Grips
TR Shaft
TR Pitch Slider
TR Thrust Bearing
Snap-On Retainer Pitch Plates
2mm Hex Nuts
Original O-ring Dampers
Original Clutch Dampers
$850 shipped & insured to lower 48. Paypal accepted if buyer covers 3% fees.
Feel free to PM me with any questions.
-Baron Johnson