TM 14 questions for Europe region

[Team Japan]

Here is one.
http://www.runryder.com/helicopter/t397358p1/



David

Hi David,

Thank you very much for your prompt response.
It is very useful as I have been struggling how to use TM-14 sold in U.S.A. outside U.S.
Will digest this post carefully.

Thanks, Team Japan

[Team Japan]

Here is one.
http://www.runryder.com/helicopter/t397358p1/



David

Hi David,

Thank you for advising the link for changing the area code of 14MZ.
Aread code on 14MZ was sucessufully changed. Thanks again.

Now, a friend of mine who has 12Z would like to change the area code.
However I am unable to find the link where contains following programs;
1) T12ZSETRX.ini
Execute T12Z Setting Rx Program

2) T12ZTESTLIGHT.ini
Execute T12Z Reduced Test

3) T12ZTEST.ini
Execute T12Z Test Program


It would be great if you could advise the place to down load above.


Best regards, Team Japan

[DavidH]

That is the commands you need. Those are the programs you posted. You have to put the one you want to use on the CF card. Needs to be the only command on the card.

David

[sambogosse]

Being in france, your not go all the frequencies in the 2.4 ghz that the rest of the world has. Or some of them will only be used at 10mw output while the rest will be at 100 mw output.

Hi,

I just received my TM-14 module and successfully plugged in in my 14MZ. I cheched the frequencies with a scanner and I can confirm that when positionned to "France" the module transmits only between 2400 and 2450 MHz, so Futaba did a bandwith limitation, not a power limitation (there's no output at all between 2450 and 2483 MHz).

BTW I had to change my radio to Europe version (module is europe one, bought in France). One important thing I noticed is when reverting to encoder 1.1 - 1.31 to use the calibration utility for the 14MZ, when I set the region to Europe, at reboot I loose all text in the display !! (bug seems to appear only when the radio is set to Europe, I tried America and it works well). But no panic, I just had to uprgade again to 1.21 - 1.38 and display gets back as normal for Europe zone.

A+

Sam

[Team Japan]

That is the commands you need. Those are the programs you posted. You have to put the one you want to use on the CF card. Needs to be the only command on the card.

David

Hi David,

I'm little bit confused. I was not able to find the v1.31 for 12Z.
Are you suggesting for me to use v1.31 of 14MZ of following program (which included in utility soft （includes T14mzUtility calibration utility for the FX40 )to apply 12Z by installing each program for different CF card to change the region code?
1) T14ZSETRX.ini
Execute T14Z Setting Rx Program
2) T14ZTESTLIGHT.ini
Execute T14Z Reduced Test
3) T14ZTEST.ini
Execute T14Z Test Program

Appreciate your help.

Best regards, Team Japan

[DavidH]

This thread explains it.
http://www.helifreak.com/showthread.php?t=20745

You can not load 14MZ updates into the 12Z.
The latest update for the 12Z is for the 2.4ghz module.
It is V1.2.0 /1.38

Just curious if your in Japan. 2.4 ghz is not legal for aircraft there yet from what I understand. Suppose to be legal around June/July is what I was told.

David

David

[Team Japan]

This thread explains it.
http://www.helifreak.com/showthread.php?t=20745

You can not load 14MZ updates into the 12Z.
The latest update for the 12Z is for the 2.4ghz module.
It is V1.2.0 /1.38

Just curious if your in Japan. 2.4 ghz is not legal for aircraft there yet from what I understand. Suppose to be legal around June/July is what I was told.

David

Hi David,

Thank you very much for your very useful information. I believe I can understand how to activate calibration soft for 12Z which is already installed in 12Z.

I do not know when 2.4G is legalized in Japan but our team is very much interested in this new way to avoid interference. So I asked your help.

Thanks again and best regards, Team Japan

[sukjoon324]

Hi, Team Japan and David.

I have same problem with Team Japan.
I'm looking for the software for 12Z but I can't find out from rcfan.
I'm really happy if you send me a software by PM or e-mail.

Thanks, Sukjoon Kim

[magic]

Hi there
I want to buy Futaba FASST receivers from the US.
Does anyone know if the receivers are region coded?
Will they work with a European TM 14 module?
Thank fpr your help
Roland

[fritzchris]

Hi

The receivers are not region coded.
You can take the receiver from the US.

mfg Chris