jmizoguchi
01-27-2008, 08:38 PM
Today. I was doing fine and end up crashing not hard but hard enough to break flyber holder and blades. nothing I would worried about but here is some story.
most of my stuff is upgraded with bladecx2.com stuff and I also have xtreme180 motor.
since I broke the flyber holder (plastic head). I did not had replacment parts but I had some Al. head that came with my CS2 with small mod to fit it. I try with all the parts I had with heli and fly again. just can't fly ... out of control. . I fight for hours looking and checking few thing.
before I forget, ever since I got the xtreme 180 motor I always had ruder issue that I had gain up proportion up all the way in 3 in 1 and all the way to the left on trasmitter. although it was just fine but I always had doubt there is some issue somewhere.
Now back again. with all the parts same except the AL. Head I tried but not working great. I even put training gear to help to find rather break thing.
do this evening. I put all the stock blade. upper/lower etc back to normal. new thing.. I was able to fly with training gear for time being but found out. When I'm up in the air, fly for say 10sec and show hesitation of either motor is going slow or too fast. Not show what is going on but almost like motor quits for mill second and come back so it will do like knocking motion but does every 10~15sec. never did this with bladecx2 blade and parts.
I was wondering if this some issue on 3 in a or is it motor? any though..
is this gyro is going bad ?
I'm adding as I go.. with stock blade, since rudder is all the way left and proportional is increased all the way.turning the heli around toward right is fine but going left if almost can't do.. when I was testing with bladecx2.com parts it was not this bad. wonder what is going on.
only reason I went to stock blade is that flyber and link did quit work well with parts (bladecx2) and figure try stock one.. how bad can it be. .. I guess.. I could try bladecx2 parts back up and if I get this funny hesitation.
most of my stuff is upgraded with bladecx2.com stuff and I also have xtreme180 motor.
since I broke the flyber holder (plastic head). I did not had replacment parts but I had some Al. head that came with my CS2 with small mod to fit it. I try with all the parts I had with heli and fly again. just can't fly ... out of control. . I fight for hours looking and checking few thing.
before I forget, ever since I got the xtreme 180 motor I always had ruder issue that I had gain up proportion up all the way in 3 in 1 and all the way to the left on trasmitter. although it was just fine but I always had doubt there is some issue somewhere.
Now back again. with all the parts same except the AL. Head I tried but not working great. I even put training gear to help to find rather break thing.
do this evening. I put all the stock blade. upper/lower etc back to normal. new thing.. I was able to fly with training gear for time being but found out. When I'm up in the air, fly for say 10sec and show hesitation of either motor is going slow or too fast. Not show what is going on but almost like motor quits for mill second and come back so it will do like knocking motion but does every 10~15sec. never did this with bladecx2 blade and parts.
I was wondering if this some issue on 3 in a or is it motor? any though..
is this gyro is going bad ?
I'm adding as I go.. with stock blade, since rudder is all the way left and proportional is increased all the way.turning the heli around toward right is fine but going left if almost can't do.. when I was testing with bladecx2.com parts it was not this bad. wonder what is going on.
only reason I went to stock blade is that flyber and link did quit work well with parts (bladecx2) and figure try stock one.. how bad can it be. .. I guess.. I could try bladecx2 parts back up and if I get this funny hesitation.