Parameters?

[Hammer94]

Where can I find a list of the stock parameters for the 400 dx6 transmitter?

For the record reset = erase all model data

[skigolfmike]

http://www.e-fliterc.com/ProdInfo/Files/DX6iDefault-Program-Settings_Blade400RTFHeli.pdf

[sokal]

that is a good settings for stock set up
with my ds285 servos my swash mix is diffrent
and end points and sub trims
so if u have other than stock that guid may not help

[LockMD]

that is a good settings for stock set up
with my ds285 servos my swash mix is diffrent
and end points and sub trims
so if u have other than stock that guid may not help


Really? I prob will put the 3400 in tonight and possible do the 285's this weekend. What did you set your parameters to?

[Hammer94]

thanks for the link Skigolfmike,I looked at E-flights site but could not find that page.

Sokal im using the 285`s and the 3400g with a 401 gyro, after I lost a servo in flight. I`m using the setting from your other post as a starting point. Only problem is I cant get the 401 to arm it has a steady flash? I will have to go back and Dbl check all connections and settings again.

[skigolfmike]

I went to www.e-fliterc.com (http://www.e-fliterc.com) , then I clicked on Blade 400 3D RTF Electric Mini Heli (http://www.e-fliterc.com/Products/Default.aspx?ProdID=EFLH1400) about 1/2 way down under New Releases. Then, in the B400 page, off to the right, above videos, I clicked Manuals and Support. On that page I clicked DX6i Default Program Settings for Blade 400 3D ... That's where I found the .pdf with the default Blade program.

[sokal]

make sue before u plug batt in on the dx61 gyro is
100 both sides on trevel adj
gyro gain is above 55%
when u plug batt in it should go to solid red
then reduce gyro gain to under 50
then set to ds, delay to 0, and adj travel as required
after your done raise the gyro gain to 80% and go down from thier for hh light should be solid red.
then unplug batt and recycle the power should have a solid red
u also may have to rebind i did seemed as if it didnt do any thing but the pros suggested i do so.
hope that helps

[sokal]

hay MD im out of town now but if help is needed will help when i have the 400 in front of me. u have to buy a 3" ext for the front servo and zip ties
find washers or bigger headed screws for the 3400 i used the rubber gromets and the screws it came with worked fine. i suggest taking the main blades of so when thier installed u can do your power on checks watch for the flybar cage contacting the blade grip usedswash mix to rid that well good luck iv found it to me a great upgrade beware she will respond alot faster then your used to.

[LockMD]

okay thanks Sokal, but how dare you go out of town when I need help :)

I think its solved, I did not reverse the gyro switch on the gyro itself.

[sokal]

i cant remember if i rev it in tx. the one on gyro u have to the tail shake to see which way it wil compinsate. rev it the tx its putting wrong direction with rudder input
also the cyclic servos rev will change from std cant remember which ones it will be.
ill be home sat or sun.

[LockMD]

Yup that was it, reversed on the gyro itself and she flies NICE pretty solid with the stock gyro and NO more tail wag. I will probably end up getting a gy401 anyhow if for nothing else but the limit settings on it.

[sokal]

http://www.helifreak.com/attachment.php?attachmentid=38195&stc=1&d=1202697712