aaron07
02-10-2008, 09:06 AM
Trex 450 SE V1.5.
AU$1000 OR MAKE ME AN OFFER for the lot inc. spares + shipping + paypal fees.
PM me for more photos.
Black CF V2 frame
CF Boom
CF aftermarket 3D horizontal + vertical fin
Neon Yellow Gorilla Gear: paddles and landing gear
Neon Yellow K+B tail blades
Futaba 401 Gyro
Futaba 9650 rudder servo
HS 65MG x3 collective servos
Jazz 40 6 18 esc
Medusa 28 40 2500 w/ 12 tooth pinion (can be used for 3S or 4S)
Factory Medusa heat-sink
V2 main gear / autorotation gear
220mm flybar
V2 fibreglass canopy
Mesh braid on esc + servo wires
Trueblood dampners
Efliernz lipo alarm
Raptor tail servo mount
+12/-12 pitch setting
3mm Carbon fibre control-rod mod (more rigid than stock, less friction)
Tail-weight mod (superior tail hold in backward flight)
Removed pulley on tail (less friction on belt)
1/2 weights in gorilla gear paddles (faster cyclic)
Fuel tubing tail mod (to reduce slop)
Plastic boom block + and tail pulley (aluminum optional) both included. (to save weight)
3 Hyperion 14.8V litestorms 2100 16C (30 cycles ea.)
1 Align Aluminum carrying case
Cost me: (approx.)
$800 aftermarket extras
$300 4S lipos
$470 original heli
$250 spares
$1820 total cost (+ more!!)
shipping of all of the individual parts imported from the USA.
Check www.helifreak.com for info on mods
Review prices from helidirect / rc hover / readyheli / wattsuprc
Spares:
1 325 pro wooden blades (new)
3 220mm flybars
1 set trueblood dampners
3 feathering shafts
1 set of control linkages
3 main shaft sleeves
2 main shafts
2 gear cases
1 extended battery mount
2 skids
2 standard cf horizontal fins
1 3D cf horizontal fin
1 standard cf vertical fin
3 tail shafts
1 tail contol guide
1 rear tail slider unit
4 V2 auto-rotation gears
3 V2 main gears
4 ceramic main bearings
2 standard main bearings
misc bearings for whole heli
1 V2 Align paddles
1 set align batman tail blades
2 cf booms
3 gates belts
Misc cf boom supports
1 set upper frame (silver)
2 sets take off and land wooden blades
1 11/12/13/15 tooth pinion
3 sets HS-65 karbonite gears
3 HS 65MG spare gears
1 Futaba 9650 gear set
1 Align pitch guage
1 K2 cnc swash levelling tool
1 K2 tail-weight mod drill jig + weights
1 main bearing press
1 box of misc screws for whole heli
AU$1000 OR MAKE ME AN OFFER for the lot inc. spares + shipping + paypal fees.
PM me for more photos.
Black CF V2 frame
CF Boom
CF aftermarket 3D horizontal + vertical fin
Neon Yellow Gorilla Gear: paddles and landing gear
Neon Yellow K+B tail blades
Futaba 401 Gyro
Futaba 9650 rudder servo
HS 65MG x3 collective servos
Jazz 40 6 18 esc
Medusa 28 40 2500 w/ 12 tooth pinion (can be used for 3S or 4S)
Factory Medusa heat-sink
V2 main gear / autorotation gear
220mm flybar
V2 fibreglass canopy
Mesh braid on esc + servo wires
Trueblood dampners
Efliernz lipo alarm
Raptor tail servo mount
+12/-12 pitch setting
3mm Carbon fibre control-rod mod (more rigid than stock, less friction)
Tail-weight mod (superior tail hold in backward flight)
Removed pulley on tail (less friction on belt)
1/2 weights in gorilla gear paddles (faster cyclic)
Fuel tubing tail mod (to reduce slop)
Plastic boom block + and tail pulley (aluminum optional) both included. (to save weight)
3 Hyperion 14.8V litestorms 2100 16C (30 cycles ea.)
1 Align Aluminum carrying case
Cost me: (approx.)
$800 aftermarket extras
$300 4S lipos
$470 original heli
$250 spares
$1820 total cost (+ more!!)
shipping of all of the individual parts imported from the USA.
Check www.helifreak.com for info on mods
Review prices from helidirect / rc hover / readyheli / wattsuprc
Spares:
1 325 pro wooden blades (new)
3 220mm flybars
1 set trueblood dampners
3 feathering shafts
1 set of control linkages
3 main shaft sleeves
2 main shafts
2 gear cases
1 extended battery mount
2 skids
2 standard cf horizontal fins
1 3D cf horizontal fin
1 standard cf vertical fin
3 tail shafts
1 tail contol guide
1 rear tail slider unit
4 V2 auto-rotation gears
3 V2 main gears
4 ceramic main bearings
2 standard main bearings
misc bearings for whole heli
1 V2 Align paddles
1 set align batman tail blades
2 cf booms
3 gates belts
Misc cf boom supports
1 set upper frame (silver)
2 sets take off and land wooden blades
1 11/12/13/15 tooth pinion
3 sets HS-65 karbonite gears
3 HS 65MG spare gears
1 Futaba 9650 gear set
1 Align pitch guage
1 K2 cnc swash levelling tool
1 K2 tail-weight mod drill jig + weights
1 main bearing press
1 box of misc screws for whole heli