Logo 600 3D Setups

[Allkind]

What kind of setup do you have with your Logo 600 3D?
What kind of results are you getting?

[Allkind]

So far i will be going with the following:
(will fill in the blanks once i have decided)

Servos - 3 x Futaba BLS451
Tail Servo - Futaba BLS251
Reg - Duralite
Flight pack - Thunder power 2000mah 2s
Motor -Actro 24-4
ESC -Jazz 55-10-32
Blades - Radix 600 , cy 95 tail
Battery - FP 3700mah 10s
RX - Futaba 149dp
Flybarless - V-bar

[cptsnoopy]

Logo600-3D with V-Stabi

9451's on cyclic and BLS-251 on tail

Align 6amp linear voltage regulator powered by TP2s-1320prolite

Spectrum AR7000/DX-7

Zpower Z50A-800 13t/153t, SAE SD-85N esc, 10s-3700evo20 (want to use 12s but I don't know if they will be making the 12t HB pinion)

NHP 620 mains and Rotor-tech 95 tail blades

AUW is 7lbs 10ozs

Headspeed is currently 2050 and I get 6 minutes using about 2650mah. My wattage peaks are only around 2100 to 2300 though so the flying is pretty tame compared to some I have seen.

[OICU812]

6003D Vstabi x3
8717 on cyclic at 8.4volts
BL251 Futaba on Tail
Jazz 55-10-32 ESC "Until" Jive 100+HV are out
Motor options: 32-3Actro on 19tooth, Orbit 30-12HE on 17tooth, NEU 1912(H)-1Y on 13tooth
AR9000 receivers in all for more robust powerbus and link up
Vblades 600mm on mains, 95mm on tails "for now" still testing blades etc...

All these systems on my setup are 3600-4000watts.

[Mercuriell]

Servos - 3 x Hitec 6965
Tail Servo - Futaba 9256
Reg - Align 6A
Flight pack - Align 19002s
Motor - ZPower Z50-800A
ESC - Jazz 55-10-32
Blades - Radix 600 , K&B 89 tail
Battery - FP EVO 25 3700 10S
RX - AR700
Flybar

Just awe inspiring performance - fastest machine on the field nitro or electric - precise power just when and where you want it - definitely the Porsche of the air !

[MrMel]

6003D Vstabi
BLS451's
9256 on the tail
Jazz 55-10-32 ESC (heat sink mod)
FP EVO25 - 10s1p 4350 packs.
Currently Orbit 30-12HE with 16T, 2200 RPM. Used Actro 32-3 with19T but currentdraw was a bit high for my liking.
AR9000 receiver
Vblades TST 600mm
92mm Tailblades with QuickUK Raptor 50 hub.


Performance: Unboggable

[MrRoth]

600 3D Vstabi
JR 8717 on cyclic at 8.4volts
9251 on the tail
Jazz 55-10-32 ESC (heat sink mod)
FP EVO25 - 10s1p 4350 packs.
Current: Orbit 30-12 with 16T. But will change to an Orbit 30-12HE with 17T tomorrow. Used Actro 32-3 with19T but currentdraw was a bit high for my liking. Also tried Tango 45-7 with 14T, most effective motor but not as strong as the Orbit and Actro
JR 921 receiver
Vblades TST 600mm
105mm Tailblades
FP 2100 RX pack with Spektrum Dual Output Regulator for the tailservo

[jamesotron99]

in my sig.