How to setup the ESky TWF-SZ 0406A 6CH Transmitter For Flight Simulators

[DierWolf]

Step 1
Turn OFF the remote, remove the crystal (TX+RX) from the transmitter.
Make sure the HOV. PIT is set to min. value:

http://i25.tinypic.com/2wedr36.jpg


Step 2
Remove battery case.

http://i31.tinypic.com/25m4o.jpg


Step 3
Find the jumper, SET:
Jumper: 2 (TOP) to OFF (RIGHT)
Jumper: 1 (BOTTOM) to ON (LEFT)

http://i30.tinypic.com/2gxjsq0.jpg


http://i29.tinypic.com/osc0eu.jpg

Step 4

Plug the XTR cable, turn on the TX and open the XTR simulator:
Go to Menu --> Radio --> Assign Channel

http://i27.tinypic.com/i50tat.jpg

This works for AeroFly Professional Deluxe, and Reflex XTR (So far, verifying more)

:tongue

[Ber60]

And the same works for AeroFly Professional Deluxe

[Ber60]

Change the title now to just flightsim.
make it a sticky , seen the same question about the tx 100 times :roll:

[soulbro]

Question.

I've made the change and it works perfect with fms. Easy flight sim!!
But now i've put the jumpers back in there old position to use with the helikopter. My hover pitch button doesn't work anymore.
Crashed the damm thing without beïng airborn.

What did I do wrong? Is there something you must do to reset the transmitter?

Robin

[Ronniebiggs]

Wont work on my Reflex flight sim. Done everything then when I load up the game it says that it cant detect the controller. When I try and go into the assign channel it wont let me as its not selectable (eg its grey and you cant click it)

Any Suggestions?

Andy

[Ber60]

Question.

I've made the change and it works perfect with fms. Easy flight sim!!
But now i've put the jumpers back in there old position to use with the helikopter. My hover pitch button doesn't work anymore.
Crashed the damm thing without beïng airborn.

What did I do wrong? Is there something you must do to reset the transmitter?

Robin

Sorry for this late reply
the hover pitch button/pot has a dedicated input on the processor of the stock tx so I think there is probably a loose wire in the tx

Wont work on my Reflex flight sim. Done everything then when I load up the game it says that it cant detect the controller. When I try and go into the assign channel it wont let me as its not selectable (eg its grey and you cant click it)

Any Suggestions?

Andy
Do you connect the tx before you start the flight sim ?

[Ronniebiggs]

Sry Ber yes I do

[Ber60]

Do you have the right cable for the job ? ( tx to usb )
Try it with fms I know it works with it (a free sim), good for checking if its works.

[Ronniebiggs]

Yes its the TX to USB

Will quickly try now.

[Ronniebiggs]

Cant seem to get it to work with the FMS.

Do you have to put the batterys in the controller? As when I previously had them in this FMS worked but I dont have them in at the moment.

[Ber60]

Cant seem to get it to work with the FMS.

Do you have to put the batterys in the controller? As when I previously had them in this FMS worked but I dont have them in at the moment.

Yes ,no batt no play

[Ronniebiggs]

lol will have another go:arggg:

:YeaBaby:

[Ronniebiggs]

No wont work? Says No Reflex interface can be detected?

[Ber60]

and in fms ?

[Ronniebiggs]

Some of the channels work. For example the right stick. The throttle channel works but not the rudder. Never flew on it as I would have to change the channel numbers etc. But it appears most works on it.

[Ber60]

Okay go to start, control panel, game controllers or joystick and setup your tx

[Ronniebiggs]

Found the options then got lost trying to calibrate!

Rotate for x axis then y then z WTF? didnt have a clue which to move and when

It was more for joy pads etc

[Ber60]

Sorry, can't help anymore cause I am modded my cable for a futaba tx perhaps one of my friends can help you further

[Ronniebiggs]

No problem I understand its frustrating trying to tell someone how to do something.

Will do without. I use a wingman controller on a flight sim I have but would have been nice to use my TX on the comp.

O well

Thx Ber

Andy

[dvshooter]

Hey all, new member. Planning to get a Belt CP when the tax return rolls in. also waiting as everyplace on the planet is out of stock, apparently because the transmitters are all being upgraded to 2.4 ghz. Place I spoke to said sometime in June for new CP's.

Anyway, controller/sim question about the cable:

I've googled "TX to USB" cable and only found cell phone cables that in no way look like they'll fit the round plug on the controller. Does the cable come with the Belt CP? I saw an "out of the box" pic of the 99$ Dauphin by Esky and it does. If not, is it something Radio Shack or a hobby store will carry by itself so I don't have to pay some absurd shipping price?

Thanks

[dvshooter]

Duh...did more reading..TX is transmitter, obviously not a plug type.

Such a newb here, :shock:

[Ber60]

Hi dvshooter
This link would be a good starting piont
http://www.rc711.com/shop/product_info.php?cPath=27_24&products_id=190

[dvshooter]

6.90 online, should be about 10$ at a hobby store judging by other parts prices...thanks Ber, know what it looks like now.

That add says it's included with all Esky heli's...but they're not the manufacturer:thinking We'll see.