www3pin
04-19-2008, 05:44 PM
Hello everybody
I recently ordered my self a CopterX, which is going to need some equipment to get into the air. So I am clearing out my RC shed
The reason for this post is to see if anyone of you heli flyers would be interested in a 1/10 Scale Nitro Car?
This car in particular is practically new, it has made not even a kilometer of driving (which you can see in the picture that shows the bottom of chassis), the differentials and all components are therefore*new* though the car has been in my shed, forgoten for quite a while...i decided I want someone to actually use it instead of it gathering dust...
it is ARTR (almost ready to run)
http://img135.imageshack.us/my.php?image=19042008014xl5.jpg
http://img261.imageshack.us/my.php?image=19042008015ux1.jpg
The package includes:
1x RS4 3 Type-SS (was a kit)...not a racing chassis by any means, but it is a very forgivable (very hard to bust up from what I have heard), 4 wheel drive vehicle, that is perfect for bashing on parking lots and for some 4wd drifting(have a verys similair but electric 1/10)...really a fun chassis for those windy days when you cant get your chopper in the air
-the chassis has two gears with a top speed of about 45-55 mph (IIRC) and even higher with provided red spur...
-comes with HPI 12R SS engine, good for about 1hp (not even broken in)
-Saleen S7 body shell expertly painted by me
1xFutaba 2PHKA MJ Radio Package (72mHz I was in the stated when I bought it, i wont tell if u dont (S3003 servos all around, their cool for bashing)
1xFront C-Hubs-anodized aluminum (from what i remember the only "weak" point of chassis) so i replaced the plastic with alu
1x red high spur gear---(gives higher top speed)
+plus some extra parts that I have for this car...(clutch bearings, sport clutch)
The car is in great condition...as I said it is practically brand new (not age terms, but wear terms) and has many miles ahead of it...the only reason it is being marked as ARTR is the fact that it is missing the pilot shaft (part# A805) and spring holder on rear left shock (part no. A471), altogether there parts should be like 6 pounds or even less, they are really tiny minuscule parts, yet the only reason that the car is new and unused is the pilot shaft (i stripped a screw in it after I broke-in the engine on its only tank of fuel , and was too lazy to get a new one, well a mix of lazy and busy
What I want to trade for are the following parts (not necessarily all of them, hit me with an offer).
-A good Tx/RX
-A decent gyro logitech 2100t above (gy401 would be nice)
-brushless motor and esc (for CopterX...so basically all T-REX 450 motors and escs apply)
-perhaps some nice MG servos
I live in Slovenia, so I would prefer to do business in Europe.
A payapl transaction in which 1 eur is sent both sides will ensure due-diligence...and give true ID. (been ripped off on the net too many times)
This is a really great way to get into another aspect of RC which is also extremely entertaining and great for windy days
Thanks you
www
I recently ordered my self a CopterX, which is going to need some equipment to get into the air. So I am clearing out my RC shed
The reason for this post is to see if anyone of you heli flyers would be interested in a 1/10 Scale Nitro Car?
This car in particular is practically new, it has made not even a kilometer of driving (which you can see in the picture that shows the bottom of chassis), the differentials and all components are therefore*new* though the car has been in my shed, forgoten for quite a while...i decided I want someone to actually use it instead of it gathering dust...
it is ARTR (almost ready to run)
http://img135.imageshack.us/my.php?image=19042008014xl5.jpg
http://img261.imageshack.us/my.php?image=19042008015ux1.jpg
The package includes:
1x RS4 3 Type-SS (was a kit)...not a racing chassis by any means, but it is a very forgivable (very hard to bust up from what I have heard), 4 wheel drive vehicle, that is perfect for bashing on parking lots and for some 4wd drifting(have a verys similair but electric 1/10)...really a fun chassis for those windy days when you cant get your chopper in the air
-the chassis has two gears with a top speed of about 45-55 mph (IIRC) and even higher with provided red spur...
-comes with HPI 12R SS engine, good for about 1hp (not even broken in)
-Saleen S7 body shell expertly painted by me
1xFutaba 2PHKA MJ Radio Package (72mHz I was in the stated when I bought it, i wont tell if u dont (S3003 servos all around, their cool for bashing)
1xFront C-Hubs-anodized aluminum (from what i remember the only "weak" point of chassis) so i replaced the plastic with alu
1x red high spur gear---(gives higher top speed)
+plus some extra parts that I have for this car...(clutch bearings, sport clutch)
The car is in great condition...as I said it is practically brand new (not age terms, but wear terms) and has many miles ahead of it...the only reason it is being marked as ARTR is the fact that it is missing the pilot shaft (part# A805) and spring holder on rear left shock (part no. A471), altogether there parts should be like 6 pounds or even less, they are really tiny minuscule parts, yet the only reason that the car is new and unused is the pilot shaft (i stripped a screw in it after I broke-in the engine on its only tank of fuel , and was too lazy to get a new one, well a mix of lazy and busy
What I want to trade for are the following parts (not necessarily all of them, hit me with an offer).
-A good Tx/RX
-A decent gyro logitech 2100t above (gy401 would be nice)
-brushless motor and esc (for CopterX...so basically all T-REX 450 motors and escs apply)
-perhaps some nice MG servos
I live in Slovenia, so I would prefer to do business in Europe.
A payapl transaction in which 1 eur is sent both sides will ensure due-diligence...and give true ID. (been ripped off on the net too many times)
This is a really great way to get into another aspect of RC which is also extremely entertaining and great for windy days
Thanks you
www