Scott Graham
04-28-2008, 07:12 PM
$599 Plus Shipping
** Does not include tail servo or reciever for $599, only if you ask for RTF adds $100**
This Heli is over 100 Grams lighter than the V2 for better 3D performance
1 - T-Rex 450 SE
1 - 430L Motor ( on the heli )
1 - Set of Black V2 Carbon Fiber Side Frames ( on the heli )
1 – Upgraded Carbon Fiber Tail Boom
2 - Sets of Hyperion Blades ( One set is on the Heli)
1 - Set of Curtis Youngblood Main Blades ( small tip chip, dropped a blade at the field )
1 - Set of Align Carbon Blades
3 - Hitec HS-65HB **Upgraded to MG for 3D flight** ( on the heli )
1 - Align 35A ESC ( on the heli )
2 - Upper V1 Main Drive Gear
1 - Lower V1 Main Drive Gear
1 - V1 One Way Bearing
1 - Complete V2 Main Drive Gear Set ( on the heli )
1 - Align "Unbreakable" Landing Gear set ( on the heli )
1 - GY401 Gyro 1 - Carbon Tail Push Rod ( on the heli )
1 - V2 Tail Grips and hub ( on the heli )
1 - Align Blade Holder
1 – New CF Tail Fin Set
1 – Full Silver Side Frame Set ( Left side upper frame damaged removing the tail servo had to be cut away )
3 - Canopy's, Fiberglass Painted Yellow Blue, One Stock Align, One Clear Painted Blue Flames ** Signed By Jason Bell Sponsored by Flight Power and Avant.
2 – Thunder Power Extreme 2070 Lipo packs Great for hard 3D flight
1 – set of Hyperion CF Tail Blades best tail blades flying ( on the heli )
1 – set of Align “Bat Wing” Tail Blades
3 – Feathering shafts
1 – extra Main shaft
1 – Extra flybar Rod
1- Extra set of Align CF look Paddles
2 – Sets of Trueblood engineering RED dampeners ( one set on the heli )
1 – Align Original Parts Case
+ The Original Manuals
I Love this T-Rex, The Heli can do anything you throw at it from piro flips to tic tocs it has what you need. Also a great starter Heli.
** Does not include tail servo or reciever for $599, only if you ask for RTF adds $100**
This Heli is over 100 Grams lighter than the V2 for better 3D performance
1 - T-Rex 450 SE
1 - 430L Motor ( on the heli )
1 - Set of Black V2 Carbon Fiber Side Frames ( on the heli )
1 – Upgraded Carbon Fiber Tail Boom
2 - Sets of Hyperion Blades ( One set is on the Heli)
1 - Set of Curtis Youngblood Main Blades ( small tip chip, dropped a blade at the field )
1 - Set of Align Carbon Blades
3 - Hitec HS-65HB **Upgraded to MG for 3D flight** ( on the heli )
1 - Align 35A ESC ( on the heli )
2 - Upper V1 Main Drive Gear
1 - Lower V1 Main Drive Gear
1 - V1 One Way Bearing
1 - Complete V2 Main Drive Gear Set ( on the heli )
1 - Align "Unbreakable" Landing Gear set ( on the heli )
1 - GY401 Gyro 1 - Carbon Tail Push Rod ( on the heli )
1 - V2 Tail Grips and hub ( on the heli )
1 - Align Blade Holder
1 – New CF Tail Fin Set
1 – Full Silver Side Frame Set ( Left side upper frame damaged removing the tail servo had to be cut away )
3 - Canopy's, Fiberglass Painted Yellow Blue, One Stock Align, One Clear Painted Blue Flames ** Signed By Jason Bell Sponsored by Flight Power and Avant.
2 – Thunder Power Extreme 2070 Lipo packs Great for hard 3D flight
1 – set of Hyperion CF Tail Blades best tail blades flying ( on the heli )
1 – set of Align “Bat Wing” Tail Blades
3 – Feathering shafts
1 – extra Main shaft
1 – Extra flybar Rod
1- Extra set of Align CF look Paddles
2 – Sets of Trueblood engineering RED dampeners ( one set on the heli )
1 – Align Original Parts Case
+ The Original Manuals
I Love this T-Rex, The Heli can do anything you throw at it from piro flips to tic tocs it has what you need. Also a great starter Heli.