Trex700 Build videos!

[Finless]

Mine is OK but I have seen new 600 nitro's with this new locking tail case design like that. They didn't get the locking hole drilled in the end of the boom perfectly 90. All you have to do is file it oblong and you can adjust the case then.

Bob

[derelict]

pretty good idea !! haven't thought about that ! (allthough i don't like the filing :-))

thank you very much for your support bob !!

Marcel

[Nightman]

Can you give out the part numbers of all the extra parts that you had to get some of them I can't seem to find anywhere by your desicription. Please.

[Finless]

Huh? Parts I I had to get? There were no parts I had to get..... I have no clue what your asking?

Bob

[jared_of_atlanta]

Maybe he means the not kit parts (motor, servos, etc).

[Nightman]

That correct things like the motor, servos, gyro, smartcarb, receiver, and anything elase that did not come in the 700 kit.

[gr8t1dini]

Have you had the chance to do the video on how to tune and get the CS dialed in?

[Finless]

Setup of the CS is no different than my 600 nitro. I have a video on install and setup of it already.

Bob

[Nightman]

We seem to be tlking about the wrong things I was not talking about setting it up I am talking about part numbers an example would be shown below.

Engine - Part # Would Be

Kasama Header - Part # Would Be

Gyro - Part # Would Be

Regulator - Part # Would Be

And so on till all the parts that were not in the 700 are listed

[jared_of_atlanta]

Watch the what's in the box video. It's all very common stuff - grandrc.com should have it all. Not sure anyone here wants to find part numbers for all the stuff -- that's your job :-).

[Nightman]

On the videos they are talking about a O.S. .91 Non-Pump

Well where I checked there no such animal that I can find that is why I am asking it makes it a lot easier on my end or job

[derelict]

Nightman...

here is the link to that motor on grandrc:
http://grandrc.com/inc/sdetail/125945

and on readyheli:
http://www.readyheli.com/O_S_91SZ_H_Ringed_w_60M_C_Carburetor_p/18300.htm

have a look at the various setup threads like this:
http://www.helifreak.com/showthread.php?t=82666 or http://www.helifreak.com/showthread.php?t=67731

These should answer most of your quesions!

Greets Marcel

[Nightman]

Thanks a lot for the information. If you find any more please let me know. The more information the better.

[PacketSpike]

Build starts today!

So much fun.

Till I need help... then good old Bob is here ;-)

Thanks Bob

[Nightman]

I have noticed that there are a few different modles of the JR X9303 I have listed them below can you tell me what one you used for the build.

JR X9303 2.4 A/S TX W/DSM 9Ch RX, 4-821 SX Mode 1
JR X9303 2.4 Heli TX W/DSM 9ch RX, 4-821 SX Mode 1
JR X9303 2.4 Heli TX W/DSM 9ch RX, 4-821 SX Mode 2
JR X9303 2.4GHz Heli Radio TX W/JRDSM 9ch RX Mode 2

[TooLy]

HI,

I have the JR G7703D with the 8900 servo on my T-rex 700N.
When I first set it up, do I have to first use it in rate mode and play with the pushrod until it's working good and than go to head lock mode, or I can just run head lock mode from the begining with zero pitch in the tail blades ?
Also, if someone have tried it on the 700N, what arm size do you use ?

Thanks,
Roei

[j bomb]

Try reading this thread on the G7703D:
http://www.helifreak.com/showthread.php?t=78591

[huskynox]

Finless,

How long did that Align clunk line last ya? Or is it still going strong? Just curious as I used it too. It doesn't seem to be swelling or anything.....

[Finless]

So far so good!

Bob

[huskynox]

Cool, thanks. I've only run 7 tanks through mine, so......?

[jamin_00]

I'm glad these are on here as I'll need them next week :)

[propeto13]

after watching several of ur build videos my new fav. word is "bear-with"
can't wait to get myn' and start building.. new here but i've been doing some lurking.

[wyorcflyer]

Bob:

You said to check back in six months with regard to a comparison of the Aurora and T700. It is about that. How would you compare the personalities, performance and reliability of the two.

Thanks

Jack

[judojamesg]

Bob,

When you did the left rudder thing for the gyro, would this make the heli pirouette like mad if the connection is lost to the Rx? i.e failsafe is full left rudder??

Jim

[Finless]

Bob,

When you did the left rudder thing for the gyro, would this make the heli pirouette like mad if the connection is lost to the Rx? i.e failsafe is full left rudder??

Jim

Huh? Left rudder thing? :thinking:thinking:thinking:thinking

Bob