jiberjaber
05-28-2008, 05:55 PM
Kasama Raptor rotor head with grip bearings, new red dampers and a new feathering spindle installed.
All you need to add are the links, the flybar and paddles (and a heli!).
Bought in January and flown a few times. Now redundant as I have replaced the Raptor Titan this was on with a Knight 3D.
Looking for £115 UKP ONO
Price includes standard royal mail postage to mainland UK only, shipping may be extra outside that area.
Payment can be by cash in person, paypal or cheque. Paypal prefered.
If paying by cheque then the goods will be despatched upon cleared funds.
Collection by prior agreement in Essex area.
Item advertised elsewhere.
FEATURES (from the web)
Main rotor hub
64 grams
Machined from 7075 T6 aluminum
Hub mounts using a pin and clamp design.
Clamp design eliminates hub rocking on the shaft yielding crisp, 3D performance.
Hub comes with four bearings pre-installed
Flybar control arm
18 grams
Machined from 7 series aluminum
The control arm is a single sided design allowing for easier disassembly and adjustment.
Washout set
16 grams
Mixing arms are machined from 5 series aluminum
Washout arms are equipped with set screws to secure the washout linkage pivot pins. (washout links and pivot pins are not included)
Flange bearings are included and pre-installed.
Washout arms are machined with an additional control hole yielding increased control and response.
Washout base
Machined from 7 series aluminum.
Washout base is taller than stock, the result is a wider bearing surface offering smoother, low friction movement.
Mixing levers
12 grams
Machined from 7 series aluminum
Flange bearings are included and pre-installed yielding a slop free pivot point.
Mixing lever length is increased with an additional control hole allowing for more aggressive control.
Blade grips
60 grams- grips, levers and hardware
Machined from 7075 T6 aircraft aluminum
Grips are designed to be used with stock raptor bearings
Blade grip control arms are offset 3 degrees lower than stock. This allows for more leverage at extreme negative blade pitch angles.
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2179-1.jpg
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2180-1.jpg
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2181-1.jpg
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2183-1.jpg
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2187-1.jpg
All you need to add are the links, the flybar and paddles (and a heli!).
Bought in January and flown a few times. Now redundant as I have replaced the Raptor Titan this was on with a Knight 3D.
Looking for £115 UKP ONO
Price includes standard royal mail postage to mainland UK only, shipping may be extra outside that area.
Payment can be by cash in person, paypal or cheque. Paypal prefered.
If paying by cheque then the goods will be despatched upon cleared funds.
Collection by prior agreement in Essex area.
Item advertised elsewhere.
FEATURES (from the web)
Main rotor hub
64 grams
Machined from 7075 T6 aluminum
Hub mounts using a pin and clamp design.
Clamp design eliminates hub rocking on the shaft yielding crisp, 3D performance.
Hub comes with four bearings pre-installed
Flybar control arm
18 grams
Machined from 7 series aluminum
The control arm is a single sided design allowing for easier disassembly and adjustment.
Washout set
16 grams
Mixing arms are machined from 5 series aluminum
Washout arms are equipped with set screws to secure the washout linkage pivot pins. (washout links and pivot pins are not included)
Flange bearings are included and pre-installed.
Washout arms are machined with an additional control hole yielding increased control and response.
Washout base
Machined from 7 series aluminum.
Washout base is taller than stock, the result is a wider bearing surface offering smoother, low friction movement.
Mixing levers
12 grams
Machined from 7 series aluminum
Flange bearings are included and pre-installed yielding a slop free pivot point.
Mixing lever length is increased with an additional control hole allowing for more aggressive control.
Blade grips
60 grams- grips, levers and hardware
Machined from 7075 T6 aircraft aluminum
Grips are designed to be used with stock raptor bearings
Blade grip control arms are offset 3 degrees lower than stock. This allows for more leverage at extreme negative blade pitch angles.
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2179-1.jpg
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2180-1.jpg
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2181-1.jpg
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2183-1.jpg
http://www.rcheliaddict.co.uk/classifieds/data/15/large/DSCF2187-1.jpg