show me your wiring!

[CoronaL]

Trying to figure out how I want to place my Rx, 2n1, battery etc..
Need some inspiration plz

[Edvard R]

Nothing too fancy on this one... I still need to clean up the wiring a little, but this setup works pretty well.

Remember to put the 2-in-1 switch as far back as possible or you will not be able to reach it for the canopy.

[JodyJ]

Here's mine, it's not the best wiring job, but it still works :)

http://www.synergy-n9.com/trex700.htm

Jody J.

[CoronaL]

Nothing too fancy on this one... I still need to clean up the wiring a little, but this setup works pretty well.

Remember to put the 2-in-1 switch as far back as possible or you will not be able to reach it for the canopy.
OOOH!!!! Thx
I was going to put my battery on the other side, but I like your spot better :)
thx alot !!!!
John
PS how many flights do you get out of the Align 1900mah pack?

[CoronaL]

Here's mine, it's not the best wiring job, but it still works :)

http://www.synergy-n9.com/trex700.htm

Jody J.
if I had an AR7100 I'd be all over that setup :)
still waiting on mine, and it will go in my Aurora and 8717's :)

[Edvard R]

PS how many flights do you get out of the Align 1900mah pack?

I get about 5-6 flight before going to orange on the 2-in-1 - the 1900 pack is fairly inexpensive, so I have 1 extra as backup in my field box.

Happy building - remember to post some photos of your final setup...:thumbup:

[stmpngrnd]

I'm reasonably happy with this setup, the only problem I had was with the spectrum step down wire bundle comping out on the top. Someday I'll man up and go 8V...can't beleive the simplicity of some of the 8V systems that have been posted.
2 in 1 in under the tray
multi gov on the right side deck
receiver/battery on top
http://www.helifreak.com/picture.php?albumid=929&pictureid=6957
http://www.helifreak.com/picture.php?albumid=929&pictureid=6956
http://www.helifreak.com/picture.php?albumid=929&pictureid=6958

[cbdane]

Great thread and great posts. Thanks!

[Snoopyflyboy]

Not the cleanest in the world, but it will work! You tell yourself that your going to take the time to make everything neat and towards the end, in the smallest spots, all the wires are different lengths:shock:. Bunch em together and put a zip tie around them:thumbup:
55973 55974 55975

[CoronaL]

what I ended up with :)
oh and a pic of a new toy, and another of the blade stickers I had to have from Readyheli :)
http://www.helifreak.com/attachment.php?attachmentid=55988&stc=1&d=1216769201
http://www.helifreak.com/attachment.php?attachmentid=55989&stc=1&d=1216769201
http://www.helifreak.com/attachment.php?attachmentid=55990&stc=1&d=1216769201
http://www.helifreak.com/attachment.php?attachmentid=55991&stc=1&d=1216769201
http://www.helifreak.com/attachment.php?attachmentid=55992&stc=1&d=1216769201
http://www.helifreak.com/attachment.php?attachmentid=55993&stc=1&d=1216769201

[Edvard R]

Wow - you have been busy...:)

Do you normally have good results with strapping your gyro down? I tried it once and 'me heli got the shakes'...

[CoronaL]

Wow - you have been busy...:)

Do you normally have good results with strapping your gyro down? I tried it once and 'me heli got the shakes'...
yeah as long as it's not too tight :)

[Mercuriell]

Well after looking at the above pics I'm embarassed to post my pics - I guess my only lame excuse is that I'm using the Flighttech 8A regulator (http://www.flightpowerusa.com/index.asp?page=Products/Product(Info.asp^currency=USD_item=FT8AVR)which has a LOT of wires and a separate Futaba glow driver - just had to have these in my box and couldn't get hold of an ALign 2 in 1. Also AR9000 and Align gov

[nwolsink]

Well after looking at the above pics I'm embarassed to post my pics - I guess my only lame excuse is that I'm using the Flighttech 8A regulator (http://www.flightpowerusa.com/index.asp?page=Products/Product%28Info.asp%5Ecurrency=USD_item=FT8AVR)whic h has a LOT of wires and a separate Futaba glow driver - just had to have these in my box and couldn't get hold of an ALign 2 in 1. Also AR9000 and Align gov

this is the messiest bunch of wiring i've seen indeed ;)

[rchflyer]

Here is how I did mine,

[derelict]

here is my wiring

[arclite5]

Here's mine. The one loose wire is from the backplate RPM sensor, it's only temporary until I can hook up the align sensor to the 7100R!

[Edvard R]

We have a typhoon here in Taiwan today, so no flying today :( Instead, I cleaned up my wiring a bit. Quite happy with it now... ;)

http://www.helifreak.com/attachment.php?attachmentid=56739&stc=1&d=1217236048

http://www.helifreak.com/attachment.php?attachmentid=56740&stc=1&d=1217236048

http://www.helifreak.com/attachment.php?attachmentid=56741&stc=1&d=1217236048

[Bobbyk]

Well after looking at the above pics I'm embarassed to post my pics - I guess my only lame excuse is that I'm using the Flighttech 8A regulator (http://www.flightpowerusa.com/index.asp?page=Products/Product%28Info.asp%5Ecurrency=USD_item=FT8AVR)whic h has a LOT of wires and a separate Futaba glow driver - just had to have these in my box and couldn't get hold of an ALign 2 in 1. Also AR9000 and Align gov

John you should be ashame of yourself, are you going to the moon with the T700N, you have more technology and wiring to land that on the moon or better yet mars.

ha ha ha

Robert

[dj_rpr]

here's some shots of mine...not finished yet and waiting on a 2nd satellite receiver

http://photos.pimped-gfx.com/albums/userpics/10001/700010.jpg

http://photos.pimped-gfx.com/albums/userpics/10001/700011.jpg

http://photos.pimped-gfx.com/albums/userpics/10001/700012.jpg

[Mercuriell]

John you should be ashame of yourself, are you going to the moon with the T700N, you have more technology and wiring to land that on the moon or better yet mars.

ha ha ha

Robert

Well messy or not it flies beautifully :happyd - did a little tidy up tonight before pouring goop over it ! At least my wiring's honest - I bet all yours looks the same where it's shoved into the frame space :nanabobo

[DJC]

here's some shots of mine...not finished yet and waiting on a 2nd satellite receiver

http://photos.pimped-gfx.com/albums/userpics/10001/700010.jpg

http://photos.pimped-gfx.com/albums/userpics/10001/700011.jpg

http://photos.pimped-gfx.com/albums/userpics/10001/700012.jpg

I'm no expert but is that your check valve I see way up buy your fuel tank? If so you should check the engine paperwork because that check valve is supposed to be close to the back plate. It makes a difference I just don't understand why.

[dj_rpr]

cheers for that , i didnt realise it had to be...anyone know the reason why?

[cbdane]

cheers for that , i didnt realise it had to be...anyone know the reason why?

I think it's because the YS diaphram pump displaces a certain volume on each stroke. The larger the volume that it is being displaced into, the smaller the resulting pressure rise. If the check valve is too far from the engine, the volume of the fuel tubing in between could drop the pressure rise on each pulse so that nothing is pumped past the check valve.

[mak]

Here is mine.