Motor Mount/gear mesh.

gevaho · 04-18-2010, 05:47 AM

Would it be wise to make slotted holes in the frame for the motor mount to easily set the gear mesh? so you move the whole mount with motor back and forth to set mesh?

Anyone try this?

JAG1 · 04-18-2010, 09:43 AM

hi,to mesh the gear,look between the front two servo's and you can just see the pinion and main gear.
good luck

gevaho · 04-19-2010, 03:03 AM

Yes I know, but to undo the motor screws you need to take the front servo's out to reach them. So if would like to do a quick pinion change you could leave the servos in and slide the whole motor mount instead of the motor.

Future1 · 04-19-2010, 01:17 PM

I'm sure it would be fine to do on the 450 Pro. The Rave has the slots as standard, and causes no problems.

life2short1971 · 04-20-2010, 09:34 AM

I don't take my servos out to reach the motor screws.

gevaho · 04-20-2010, 11:19 AM

I have phillips head screws in them, I will change them with allen ones when my new motor arrives. Then it is al lot easier to get them out.

And I am using Towerpro servo;s they are bigger then the 410's or the Hitecs.

Just some fiddling and it will al work out ( I hope

)

04-18-2010, 05:47 AM	#1
gevaho Registered Users My HF Map location Join Date: Oct 2009 Location: The Netherlands/Holland we speak Dutch.	Motor Mount/gear mesh. Would it be wise to make slotted holes in the frame for the motor mount to easily set the gear mesh? so you move the whole mount with motor back and forth to set mesh? Anyone try this? __________________ Compass 6HVR MSH Brain \| Scorpion HKIII 4035 560 \|YGE 90HV \| Savox 1258TG \| Align DS650 \|Futaba T8FG \| Dutch Compass Maniac's

04-18-2010, 09:43 AM	#2
JAG1 Registered Users Join Date: Feb 2007 Location: essex,uk	hi,to mesh the gear,look between the front two servo's and you can just see the pinion and main gear. good luck __________________ align 450 se v1,SOLD IT!!! got a 450 pro now!!!!! align 500,it's built!! yes it's in the air!! Blade Nano CPX

04-19-2010, 03:03 AM	#3
gevaho Registered Users Thread Starter My HF Map location Join Date: Oct 2009 Location: The Netherlands/Holland we speak Dutch.	Yes I know, but to undo the motor screws you need to take the front servo's out to reach them. So if would like to do a quick pinion change you could leave the servos in and slide the whole motor mount instead of the motor. __________________ Compass 6HVR MSH Brain \| Scorpion HKIII 4035 560 \|YGE 90HV \| Savox 1258TG \| Align DS650 \|Futaba T8FG \| Dutch Compass Maniac's

04-20-2010, 09:34 AM	#5
life2short1971 Registered Users Join Date: Jan 2009 Location: Fort White,Florida	I don't take my servos out to reach the motor screws. __________________ Scott Trex 500 / /3026-1600/CC Ice75 /3G /Ds510's/Torsion 430 fbl's Trex 450 pro/HK2221-8/ Ice 50 /HS-5065MG/325D's/Kbdd's

04-20-2010, 11:19 AM	#6
gevaho Registered Users Thread Starter My HF Map location Join Date: Oct 2009 Location: The Netherlands/Holland we speak Dutch.	I have phillips head screws in them, I will change them with allen ones when my new motor arrives. Then it is al lot easier to get them out. And I am using Towerpro servo;s they are bigger then the 410's or the Hitecs. Just some fiddling and it will al work out ( I hope ) __________________ Compass 6HVR MSH Brain \| Scorpion HKIII 4035 560 \|YGE 90HV \| Savox 1258TG \| Align DS650 \|Futaba T8FG \| Dutch Compass Maniac's

04-19-2010, 01:17 PM	#4
Future1 Registered Users My HF Map location Join Date: Apr 2008 Location: Gold Coast, Australia	I'm sure it would be fine to do on the 450 Pro. The Rave has the slots as standard, and causes no problems.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode