Upgraded my CP v2 - Page 2

Ronarse · 02-29-2012, 07:56 AM

Thanks for the input guys. I do appreciate it

jperkosk · 02-29-2012, 05:20 PM

+1 Dave
+2 Andy

Can't stress enough the importance of having upper part (50%-75%-100% of stick) of Normal and Idle-up curves (both throttle and pitch) exactly matched, so there is no transition at all from normal to idle-up and up in the air, otherwise the heli will either shoot-up or drop when switched from one to another...

That's precisely what's MI5 with a stock Esky Tx, an otherwise decent intermediate flier in my club does circuits with his Belt CP v2 in normal mode, has huge altitude hold problems when windy (which is most of the time in my place), all because he's afraid to engage idle-up. I let him hover once my TR450, and was flipping the idle-up on and off for him and he couldn't believe the lack of reaction from the heli, and wind resistance in idle-up afterwards.

Ronarse · 03-10-2012, 06:07 PM

Ok my readings are: -6,0,+6 all mid stick idle up. Can I get more pitch with the dx6i? Is there a setting to adjust?

copterboy · 03-10-2012, 06:42 PM

Yes, it easy to do with the DX6i. Go to the swashmix screen in the first menu, go over the pitch setting, and try increasing the value by 5%. Eg. 65% would become 70%. Then check your pitch range again.

You also need to check there is no binding with the top of the washout base and bottom of rotor head at high stick, should be a gap about a hair's width.

Also check the swashplate doesn't bind with frame or bearing block at low stick.

When at High/Low stick, roll the AIL/ELEV stick around to the corners so you get full movement of the swash with no binding.

Should be able to squeeze +-9/10 on a belt as I recall. But it may bog the underpowered stock motor. Think I kept mine at +-9 because of it.

Ronarse · 03-10-2012, 07:23 PM

Thanks copter boy. There is no binding what so ever. Made damn sure when I rechecked everything today.

02-29-2012, 07:56 AM	#21
Ronarse Registered Users Thread Starter Join Date: Jan 2012 Location: Ft Lee, VA	Gracias Thanks for the input guys. I do appreciate it

02-29-2012, 05:20 PM	#22
jperkosk Registered Users My HF Map location Join Date: Dec 2009 Location: San Luis Potosí, México	+1 Dave +2 Andy Can't stress enough the importance of having upper part (50%-75%-100% of stick) of Normal and Idle-up curves (both throttle and pitch) exactly matched, so there is no transition at all from normal to idle-up and up in the air, otherwise the heli will either shoot-up or drop when switched from one to another... That's precisely what's MI5 with a stock Esky Tx, an otherwise decent intermediate flier in my club does circuits with his Belt CP v2 in normal mode, has huge altitude hold problems when windy (which is most of the time in my place), all because he's afraid to engage idle-up. I let him hover once my TR450, and was flipping the idle-up on and off for him and he couldn't believe the lack of reaction from the heli, and wind resistance in idle-up afterwards. __________________ Jerry Trex 700N Pro fbl, 600N Pro x 2, 450SE v1, 250 v2 fbl, Compass 6HV fbl, Blade 450x, 400, 300x, 130x, mCPx, 120SR, mQx, mSR, Rotor Concepts HPQ1, Walkera CB180Q, CB100, Novus FP, CP, Esky Hunter, Big Lama.

03-10-2012, 06:07 PM	#23
Ronarse Registered Users Thread Starter Join Date: Jan 2012 Location: Ft Lee, VA	? Ok my readings are: -6,0,+6 all mid stick idle up. Can I get more pitch with the dx6i? Is there a setting to adjust?

03-10-2012, 06:42 PM	#24
copterboy Registered Users Join Date: May 2008 Location: Manchester, England	Yes, it easy to do with the DX6i. Go to the swashmix screen in the first menu, go over the pitch setting, and try increasing the value by 5%. Eg. 65% would become 70%. Then check your pitch range again. You also need to check there is no binding with the top of the washout base and bottom of rotor head at high stick, should be a gap about a hair's width. Also check the swashplate doesn't bind with frame or bearing block at low stick. When at High/Low stick, roll the AIL/ELEV stick around to the corners so you get full movement of the swash with no binding. Should be able to squeeze +-9/10 on a belt as I recall. But it may bog the underpowered stock motor. Think I kept mine at +-9 because of it. __________________ COPTERBOY To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. DX6i, mSR (SOLD), BeltCP (SOLD), mCPx w solid boom and Rakon Heli Head T-Rex450V2 w.PRO head, Scorp-8 & 45A V2 ESC, CSM4200/S9257, 3xHS65MG E-Flite CX2 - All Microheli/Extreme CNC CF Upgrades TRex600N, Kasama Head, OS50SX

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-10-2012, 07:23 PM	#25
Ronarse Registered Users Thread Starter Join Date: Jan 2012 Location: Ft Lee, VA	Thanks copter boy. There is no binding what so ever. Made damn sure when I rechecked everything today.