Fun, Learning, Friendship and Mutual Respect
START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Gaui Helicopters > X7


X7 Discussion and support of the Gaui X7


Reply
 
Thread Tools Display Modes
Old 03-25-2012, 01:25 AM   #1
sresener
Registered Users
 

Join Date: Jul 2011
Location: Burnaby, BC
Default 700mx

I was looking up the spec difference between a 510kv 700mx and a hkIII 4035 500kv

I notice the align claims more power but the mainshaft out of the motor is 1.8mm shorter than the scorpion

My question is can I use the 700mx without any modification and would it perform as well as the scorpion motor and would it hold up to sport/and beginning 3d.
sresener is offline        Reply With Quote
Old 03-25-2012, 01:33 AM   #2
vr360
 

Join Date: Oct 2011
Location: phoenix, az
Default

The 700mx is a good motor.

It is definitely not more powerful and probably is a bet less powerful than the HKIII equivalent.

Neither motor's stock shaft will reach the pinion support in the X7 due to the mod 1.2 gear height. If you want to change shafts you will need to buy another shaft. A member here used a KDE 700XF shaft on his 700mx and now has pinion support. There has been one member who broke a motor shaft on the 700mx's stock shaft. This is probably due to poor shaft material and the fact that the shaft takes all the axial load because the gears are so beefY!
vr360 is offline        Reply With Quote
Old 03-25-2012, 01:55 AM   #3
sresener
Registered Users
Thread Starter Thread Starter
 

Join Date: Jul 2011
Location: Burnaby, BC
Default

Thank you for the info.

I was just on kde's websight, so the KDE 700XF has the right length shaft. And if it does would a 120 amp esc be enough for that motor
sresener is offline        Reply With Quote
Old 03-25-2012, 02:07 AM   #4
_Dekker
Registered Users
 
Posts: 654
 

Join Date: Oct 2006
Location: Delft, Netherlands
Default

The 700mx has very little copper on the stator. If you are not going to rewind it you are better off with a 4035.
The 4035 shafts will also fit the 700mx, an example can be found here:
http://www.helifreak.com/showthread.php?p=3770350
For the X7 you should try to get hold of the 110mm version.

Bert
__________________
Raptor E700: PowerDekker 4235, JR DS8925HV & MKS HBL980HV, 12s, Vortex VX1n, Jive Pro 120HV, Jeti DS-16
_Dekker is online now        Reply With Quote
Old 03-25-2012, 02:00 PM   #5
ragtop01
Registered Users
 
Posts: 301
 
My HF Map location
Join Date: Dec 2009
Location: ut
Default

im the member with the kde shaft and he broken shaft. mine is a 530kv tho. if you go with the scorpion your brobably ok without upgrading the shaft to the longer one but the mx motor shaft is weak sauce for sure. im pretty hard on my helis but these other guys are abit more advanced and therfor harder on thier equipment. id run what they're suggesting.
__________________
"just let it happen"
ragtop01 is offline        Reply With Quote
Old 03-25-2012, 07:58 PM   #6
Rob Cherry
Registered Users
 
Posts: 1,171
 
My HF Map location
Join Date: Mar 2010
Location: MN
Default

Quote:
Originally Posted by sresener View Post
Thank you for the info.

I was just on kde's websight, so the KDE 700XF has the right length shaft. And if it does would a 120 amp esc be enough for that motor
Sure, if you keep your pitch under control. That motor will EASILY pull 200A continuous if you let it. Best be safe with a 160A controller. If I try hard, I can overload my 120A YGE with my HK3-560. HAHA!
__________________
E7 | E5S | E5
Team Synergy | Gens Ace | Scorpion Motors | Progressive RC | Anything Heli
Rob Cherry is offline        Reply With Quote
Reply




Unregistered
Go Back   HeliFreak > R/C Helicopter Support > Gaui Helicopters > X7


X7 Discussion and support of the Gaui X7

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Copyright © 2004-2011 - William James - Helifreak.com