Naza VU bec voltage output

Twister773 · 03-25-2012, 10:46 PM

What is it? Looking to get servos ordered tonight for my f450 and really don't want to run a seperate bec unless I have to.

Tahoe Ed · 03-25-2012, 10:51 PM

Per the Naza specs, 4.8-5.5v for voltage to the MU and therefor to your gimbal servos. I use s separate BEC and drive the servos at 6v. The CC 10A bec is not that large and is programable.

robi1kenobi · 08-04-2012, 06:32 PM

I want to use CC 10A BEC too, do I have to remove red wire from Naza VU or can I just connect CC BEC to my receiver without any modifications?

Adidas4275 · 08-05-2012, 09:01 PM

I would just use the signal wire from the NAZA and power the servos off a BEC.....

Twister773 · 08-05-2012, 09:10 PM

Quote:

Originally Posted by Adidas4275

I would just use the signal wire from the NAZA and power the servos off a BEC.....

X2. I've come a long ways since this thread started lol

robi1kenobi · 08-06-2012, 05:00 AM

OK, I'll just disconnect '+' wire from VU, thanks for the help guys

sjgusmc21 · 08-09-2012, 01:25 PM

I too would like to try this. Although apparently not as smart or advanced as many of you here.....so anyone have diagram on this type of setup? Naza/CC Bec/Servo's? Thanks.

03-25-2012, 10:46 PM	#1
Twister773 Registered Users Join Date: Oct 2009 Location: SLO, California	Naza VU bec voltage output What is it? Looking to get servos ordered tonight for my f450 and really don't want to run a seperate bec unless I have to. __________________ Nikon D4/Coming Soon/Cinestar 8/8FG super

03-25-2012, 10:51 PM	#2
Tahoe Ed Registered Users My HF Map location Join Date: Nov 2009 Location: Lake Tahoe/Las Vegas	Per the Naza specs, 4.8-5.5v for voltage to the MU and therefor to your gimbal servos. I use s separate BEC and drive the servos at 6v. The CC 10A bec is not that large and is programable. __________________ AMA #844172 DJI S800 WKM Z15 Nex5N iOSD Data Link Waypoint DJI F450 Naza + GPS with 5.8gHz vTx DJI Phantom with GoPro3, DJI F330 with Naza + GPS Align Trex 550 with WKH, Trex 500 with Naza H

08-04-2012, 06:32 PM	#3
robi1kenobi Registered Users Join Date: Jul 2011 Location: Croatia, Zagreb	I want to use CC 10A BEC too, do I have to remove red wire from Naza VU or can I just connect CC BEC to my receiver without any modifications? __________________ MSH MINI PRÔTOS

08-06-2012, 05:00 AM	#6
robi1kenobi Registered Users Join Date: Jul 2011 Location: Croatia, Zagreb	OK, I'll just disconnect '+' wire from VU, thanks for the help guys __________________ MSH MINI PRÔTOS

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-05-2012, 09:01 PM	#4
Adidas4275 Registered Users Join Date: Dec 2010 Location: Fresno,Ca	I would just use the signal wire from the NAZA and power the servos off a BEC.....

08-09-2012, 01:25 PM	#7
sjgusmc21 Registered Users Join Date: May 2007 Location: Lorton, VA	I too would like to try this. Although apparently not as smart or advanced as many of you here.....so anyone have diagram on this type of setup? Naza/CC Bec/Servo's? Thanks.