F550 with WKM ... No spin motors

Antwnis · 05-05-2012, 04:33 AM

Hello to all,
My name Antonis from Athens /Greece ,
Build a 550 with WKM ... Step by step install the program DJI WKM all ok ...
Now I have a problem, after from install the program and fix all parameter for my f550 (x/z for gps /calibrator tx / failure safe mode gps ...) don't spin the motors !!!!
I saw many others parameters from my tx (futaba 10CG ) and from my F550/ WKM / and program .
I Test esc's alone with motors and it is ok ...!!! I put Esc (without D Bus) on receiver and all Esc and motors
After all the above I understand that the D Bus *not send commands to the receiver ...
Is there a secret, any tips, something that did not, beyond the manioual and program?
Thanks
Good wishes To all.

Antonis

Antwnis · 05-06-2012, 07:07 AM

Any answer ?

worldofmaya · 05-10-2012, 01:31 AM

Just build my 550 with Futaba (but with SBus Receiver) and worked right away... did you do the both sticks into a corner action to arm your WKM?
I found this video really helpful:

Vimeo

-Klaus

petedee · 05-10-2012, 04:17 AM

You may have to adjust your throttle trim down a bit to get it to recognise low throttle for arming.

Kamikaze Pilot · 05-11-2012, 08:14 AM

"... did you do the both sticks into a corner action to arm your WKM?"

I did that yesterday

After flying my helis and planes I took the quad out AND COULDN"T GET IT STARTED.

I was so mad, I went home.

Then I realize what I'd done (or not done) DUH!

petedee · 05-11-2012, 08:58 PM

Any luck with this yet Antonis?

05-05-2012, 04:33 AM	#1
Antwnis Registered Users Join Date: May 2012 Location: Athens , Greece	F550 with WKM ... No spin motors Hello to all, My name Antonis from Athens /Greece , Build a 550 with WKM ... Step by step install the program DJI WKM all ok ... Now I have a problem, after from install the program and fix all parameter for my f550 (x/z for gps /calibrator tx / failure safe mode gps ...) don't spin the motors !!!! I saw many others parameters from my tx (futaba 10CG ) and from my F550/ WKM / and program . I Test esc's alone with motors and it is ok ...!!! I put Esc (without D Bus) on receiver and all Esc and motors After all the above I understand that the D Bus *not send commands to the receiver ... Is there a secret, any tips, something that did not, beyond the manioual and program? Thanks Good wishes To all. Antonis

05-10-2012, 04:17 AM	#4
petedee Registered Users Join Date: Sep 2011 Location: Canberra, Australia	You may have to adjust your throttle trim down a bit to get it to recognise low throttle for arming. __________________ DJI Naza 330, 450 & 550 hexa, TBS Discovery (Naza-M/5.8Ghz vid link/ET telemetry), KK2 micro hexa and micro quad, Nano Ladybird/Spektrum Hybrid, Nano MQX hybrid. 300X, Trex 450 Pro DFC, mCP X's, mSR X, nano CP X DX18, 14SG To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

05-11-2012, 08:14 AM	#5
Kamikaze Pilot Registered Users Join Date: Jan 2009 Location: Marion, Illinois	"... did you do the both sticks into a corner action to arm your WKM?" I did that yesterday After flying my helis and planes I took the quad out AND COULDN"T GET IT STARTED. I was so mad, I went home. Then I realize what I'd done (or not done) DUH! __________________ Weeeeeeeeeee!

05-11-2012, 08:58 PM	#6
petedee Registered Users Join Date: Sep 2011 Location: Canberra, Australia	Any luck with this yet Antonis? __________________ DJI Naza 330, 450 & 550 hexa, TBS Discovery (Naza-M/5.8Ghz vid link/ET telemetry), KK2 micro hexa and micro quad, Nano Ladybird/Spektrum Hybrid, Nano MQX hybrid. 300X, Trex 450 Pro DFC, mCP X's, mSR X, nano CP X DX18, 14SG To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-06-2012, 07:07 AM	#2
Antwnis Registered Users Thread Starter Join Date: May 2012 Location: Athens , Greece	Any answer ?