DFC and BeastX - Page 2

khoysagk · 05-26-2012, 02:00 PM

Test flight went fine. I'll leave it the way it is now. Long balls on outer swash and short balls on inner. I used 2 main shaft washers on the AR pin, turned out to be the perfect thickness.
Couple pics and test video attached.

YouTube (Short URL)

dbennettya · 05-26-2012, 02:32 PM

Others have used the long servo balls on the outer swash arms and then used a Gaui ball with through hole to make a AR pin with ball to match. I have some spare Gaui balls with through hole if your interested in a couple PM me and we can work it out. It would be nice to have a simple good solution to reduce the mechanical gain.

Don

khoysagk · 05-26-2012, 06:45 PM

Quote:

Originally Posted by dbennettya

Others have used the long servo balls on the outer swash arms and then used a Gaui ball with through hole to make a AR pin with ball to match. I have some spare Gaui balls with through hole if your interested in a couple PM me and we can work it out. It would be nice to have a simple good solution to reduce the mechanical gain.

Don

Thanks Don, I appreciate the offer. But I'd still have to find a long enough screw and spacer to make the pin.

youturnjason · 06-07-2012, 10:51 PM

Did anyone else have to lower their dial one on their beastx? Im sitting at start of red at 6 degrees now, which is what i was on with the old head. But i've had to lower dial 1 from 8:30 to about 7:00 to get rid of the shakes.

cajkat1073 · 06-07-2012, 11:41 PM

I set mine up per the instructions. on the DFC head I tightened the links all the way in and backed them out one full turn. Made sure the swashplate was level and set up on the 7200bx went fine. No problem with 6 degrees.

khoysagk · 06-08-2012, 06:50 AM

Quote:

Originally Posted by youturnjason

Did anyone else have to lower their dial one on their beastx? Im sitting at start of red at 6 degrees now, which is what i was on with the old head. But i've had to lower dial 1 from 8:30 to about 7:00 to get rid of the shakes.

I did. Don't remember how much though.

youturnjason · 06-09-2012, 01:58 AM

Actually turns out it wasnt the dfc head. I made a silly mistake. I replaced 2 of the inner swash balls with shorter ones for more resolution, but installed the DFC head on the 2 longer ones I didn't replace. I've taken the longer ones out to avoid that mistake in the future.

06-07-2012, 11:41 PM	#25
cajkat1073 Registered Users Join Date: Aug 2010 Location: Louisville, kentucky	I set mine up per the instructions. on the DFC head I tightened the links all the way in and backed them out one full turn. Made sure the swashplate was level and set up on the 7200bx went fine. No problem with 6 degrees. __________________ HOBBY WORLD

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-26-2012, 02:32 PM	#22
dbennettya Registered Users Join Date: Apr 2010 Location: USA	Others have used the long servo balls on the outer swash arms and then used a Gaui ball with through hole to make a AR pin with ball to match. I have some spare Gaui balls with through hole if your interested in a couple PM me and we can work it out. It would be nice to have a simple good solution to reduce the mechanical gain. Don

06-07-2012, 10:51 PM	#24
youturnjason Registered Users Join Date: Apr 2012 Location: Melbourne, Australia	Did anyone else have to lower their dial one on their beastx? Im sitting at start of red at 6 degrees now, which is what i was on with the old head. But i've had to lower dial 1 from 8:30 to about 7:00 to get rid of the shakes.

06-09-2012, 01:58 AM	#27
youturnjason Registered Users Join Date: Apr 2012 Location: Melbourne, Australia	Actually turns out it wasnt the dfc head. I made a silly mistake. I replaced 2 of the inner swash balls with shorter ones for more resolution, but installed the DFC head on the 2 longer ones I didn't replace. I've taken the longer ones out to avoid that mistake in the future.