Fun, Learning, Friendship and Mutual Respect
START  HERE


Unregistered
Go Back   HeliFreak > R/C Helicopters > Aerodynamics, Physics and Engineering


Aerodynamics, Physics and Engineering Aerodynamics, Physics and Engineering Discussions


Reply
 
Thread Tools Display Modes
Old 06-17-2012, 08:12 PM   #1
hareedy
Registered Users
 
Posts: 282
 
My HF Map location
Join Date: Sep 2008
Location: Cairo,Egypt
Default What makes some rc helis more or less sensitive to the wind ?

I have been flying rc helis for 6 years now
And I noticed through flying lots of them that some are less sensitive to the wind than others
For example the outrage fusion 50 is less sensitive than my logo 600
To tell u the truth the outrage is much more stable in the wind than the logo 600
Off course I mean 3d flying ( funnels , tic toc ....etc )


---
I am here: http://tapatalk.com/map.php?jamqsy
hareedy is offline        Reply With Quote
Old 06-17-2012, 10:55 PM   #2
desertstalker
Registered Users
 

Join Date: Apr 2011
Location: Australia
Default

How heavy are the two helis?

Like planks disc/wing loading affects stability in the wind (higher is better). For a heli more weight also makes a difference (regardless of disc loading) as there is more inertia for the wind to overcome.

Assuming they are both FB, its less of an issue with FBL helis.
__________________
-DX8
-MSH MiniProtos Stretched, SK720, DS95/DS95i, Hyp 4S 25C 2500mAh
-MSH Protos Stretched, Brain, Hyp DS16/BLS251, 6S 3000mAh
-Goblin 500, HC3SX, Hyp DH16/MKS980BL, Scorp 4015-1100
desertstalker is offline        Reply With Quote
Old 06-19-2012, 09:28 PM   #3
hareedy
Registered Users
 
Posts: 282
Thread Starter Thread Starter
 
My HF Map location
Join Date: Sep 2008
Location: Cairo,Egypt
Default

Thanks for replying
Both my logo 600 which weigh 4.2 kg with 623 mm edge blades fbl and my goblin 700 which weigh 5.1 kg and the sab 690 mm are so sensitive to the wind but the outrage fusion 50 is so stable in the wind that I couldn't believe it when I tried one although its almost the same weight as the logo and it uses the same blades and that's what got me to wonder about the design



Sent from my iPhone using Tapatalk
hareedy is offline        Reply With Quote
Old 06-20-2012, 04:50 AM   #4
kimmik
Registered Users
 
My HF Map location
Join Date: Sep 2011
Location: Australia
Default

Since they are fbl, what differences are there in setup? Ie gyro, servo and settings.
kimmik is offline        Reply With Quote
Old 06-20-2012, 07:51 AM   #5
hareedy
Registered Users
 
Posts: 282
Thread Starter Thread Starter
 
My HF Map location
Join Date: Sep 2008
Location: Cairo,Egypt
Default

All the same servos jr 8717 working on 5.5 volts and all vbar with almost identical setups


Sent from my iPhone using Tapatalk
hareedy is offline        Reply With Quote
Old 06-20-2012, 07:52 AM   #6
hareedy
Registered Users
 
Posts: 282
Thread Starter Thread Starter
 
My HF Map location
Join Date: Sep 2008
Location: Cairo,Egypt
Default

The outrage and the logo runs at 2200 hs
And the goblin runs at 2230 hs


Sent from my iPhone using Tapatalk
hareedy is offline        Reply With Quote
Old 06-20-2012, 08:10 AM   #7
kimmik
Registered Users
 
My HF Map location
Join Date: Sep 2011
Location: Australia
Default

That shouldn't be then, assuming both gains were optimized.

It's possible that damping design differences are the cause. Also if one Heli has perfect phasing and the other doesn't, that can be a cause too. My Tdr was jittery and a bit hard to hover precisely until I optimized the phasing for the specific blades.
kimmik is offline        Reply With Quote
Old 06-20-2012, 08:19 AM   #8
CeeveeSiN
Registered Users
 
Posts: 5,350
 
My HF Map location
Join Date: Sep 2008
Location: Houston Texas
Default

Quote:
Originally Posted by hareedy View Post
Thanks for replying
Both my logo 600 which weigh 4.2 kg with 623 mm edge blades fbl and my goblin 700 which weigh 5.1 kg and the sab 690 mm are so sensitive to the wind but the outrage fusion 50 is so stable in the wind that I couldn't believe it when I tried one although its almost the same weight as the logo and it uses the same blades and that's what got me to wonder about the design



Sent from my iPhone using Tapatalk
Err wait a sec you said your Goblin 700 is sensitive in the wind?

that has to be FBL setup.. as nothing short of a 50+ MPH wind is going to move a 700E anywhere you dont want it to go..

with a properly setup Vbar 5.2+ wind is non existant on any 600-700 heli for the msot part.

We fly in sustained 30+ down here during the spring and early summer and none of my large birds fight the wind at all..
hell I fly the 450 in 25ish winds with no issues.
__________________
SAB USA Field Rep, Skookum Field Rep,
Team Lynx
.
Goblin 700, Goblin 630, Goblin 500
CeeveeSiN is online now        Reply With Quote
Old 06-20-2012, 04:41 PM   #9
hareedy
Registered Users
 
Posts: 282
Thread Starter Thread Starter
 
My HF Map location
Join Date: Sep 2008
Location: Cairo,Egypt
Default

Ok Here is a video to show what I am talking about
It was a 35 km+ wind and gust up to 40 something
At the end of the funnel u will c that the heli drifts like there is no tomorrow

youtube.com/index?desktop_uri=%2F&gl=EG#/watch?v=USnRwUogcK8



---
I am here: http://tapatalk.com/map.php?j0qb1p
hareedy is offline        Reply With Quote
Old 06-20-2012, 04:42 PM   #10
hareedy
Registered Users
 
Posts: 282
Thread Starter Thread Starter
 
My HF Map location
Join Date: Sep 2008
Location: Cairo,Egypt
Default

Tomorrow I will attach my vbar file any comments will be appreciated


---
I am here: http://tapatalk.com/map.php?uo2224
hareedy is offline        Reply With Quote
Old 06-21-2012, 07:10 AM   #11
hareedy
Registered Users
 
Posts: 282
Thread Starter Thread Starter
 
My HF Map location
Join Date: Sep 2008
Location: Cairo,Egypt
Default

Quote:
Originally Posted by kimmik View Post
That shouldn't be then, assuming both gains were optimized.

It's possible that damping design differences are the cause. Also if one Heli has perfect phasing and the other doesn't, that can be a cause too. My Tdr was jittery and a bit hard to hover precisely until I optimized the phasing for the specific blades.
what do u mean by (optimized the phasing for the specific blades.)
can you please explain ?
hareedy is offline        Reply With Quote
Old 06-21-2012, 07:35 AM   #12
kimmik
Registered Users
 
My HF Map location
Join Date: Sep 2011
Location: Australia
Default

Different blades lead or lag different amount. The head has fixed phase, usually 90. This means on one set of blades, if elevator servo moves, the Heli perfectly moves in pitch only. Gyro corrections are thus applied perfectly by the blades, achieving rapid stabilization of a destabilizing event eg wind

On a different set of blades that lag say 3degrees, here's what happens in simplified explanation.

Elevator servo moves, Heli moves cosine3 in pitch, and sine3 in roll

Now gyro has to correct the roll error by using aileron swash

But then the Aileron swash actually causes a bit of pitch.

So what happens is a wobble, or precession movement of the head or body with destabilizing events. Not only does it slow down the recovery of control, but also limits the max gain usable, component wear.

If you do some quick stabs of either collective or rudder, or do a rapid stop, and see a wobble in either head or body, that means the phase is out a bit.

My experience with the Tdr is, at 4deg out, the Heli feels a bit unsteady. Piros wobble noticeably rather than being flat. Gain can't be turned high before body wobbling even at hover. Now that it has 4deg of swash lead (ie blade lags 4deg), perfect flying machine.... I'm in total awe of it!
kimmik is offline        Reply With Quote
Old 07-06-2012, 07:06 AM   #13
kimmik
Registered Users
 
My HF Map location
Join Date: Sep 2011
Location: Australia
Default

Any update?
kimmik is offline        Reply With Quote
Old 07-19-2012, 11:28 AM   #14
BladeBender
Registered Users
 

Join Date: Jul 2010
Location: Atlanta Ga
Default

I have been tinkering with an HK450V2 NOBAR projekt with a little bit of success. I am still in the "hunting the best blades" phase (no pun intended) and was curious as to how i determine the lag of a particular set of blades? This way I can optimize the phasing for each set tried. Im using an old school mechanical swash driver, seperate from rotorhead, so phasing adjustments should be possible. On a side note: does blade lag occur with any noticeable effect on the tail (i realize they woud both lag the same amount, if at all).
BladeBender is offline        Reply With Quote
Old 07-23-2012, 11:04 AM   #15
ehernan3
Registered Users
 

Join Date: Mar 2011
Location: Canton, MI
Default

Quote:
Originally Posted by kimmik View Post
Different blades lead or lag different amount. The head has fixed phase, usually 90. This means on one set of blades, if elevator servo moves, the Heli perfectly moves in pitch only. Gyro corrections are thus applied perfectly by the blades, achieving rapid stabilization of a destabilizing event eg wind

On a different set of blades that lag say 3degrees, here's what happens in simplified explanation.

Elevator servo moves, Heli moves cosine3 in pitch, and sine3 in roll

Now gyro has to correct the roll error by using aileron swash

But then the Aileron swash actually causes a bit of pitch.

So what happens is a wobble, or precession movement of the head or body with destabilizing events. Not only does it slow down the recovery of control, but also limits the max gain usable, component wear.

If you do some quick stabs of either collective or rudder, or do a rapid stop, and see a wobble in either head or body, that means the phase is out a bit.

My experience with the Tdr is, at 4deg out, the Heli feels a bit unsteady. Piros wobble noticeably rather than being flat. Gain can't be turned high before body wobbling even at hover. Now that it has 4deg of swash lead (ie blade lags 4deg), perfect flying machine.... I'm in total awe of it!
So how do you correct a situation like this(4 degrees out of phase)? How do you measure it in the first place?
ehernan3 is offline        Reply With Quote
Old 07-23-2012, 12:51 PM   #16
kimmik
Registered Users
 
My HF Map location
Join Date: Sep 2011
Location: Australia
Default

First make sure your fbl is perfectly aligned to frame

Then, start with 0deg phase, which is default, turn the cyclic gain up until you have wobbles at hover. If the wobble is single axis only, usually airleron, then no phase adjustment needed.

If the wobble is an ellipse or circle, then correction is needed. Usually advancing.

Last edited by kimmik; 07-24-2012 at 02:34 AM..
kimmik is offline        Reply With Quote
Old 07-23-2012, 10:50 PM   #17
ehernan3
Registered Users
 

Join Date: Mar 2011
Location: Canton, MI
Default

Quote:
Originally Posted by kimmik View Post
First make sure your fbl is perfectly aligned to frame

Then, start with 0deg phase, which is default, turn the cyclic gain up until you have wobbles at hover. If the wobble is single axis only, usually airleron, then do phase adjustment needed.

If the wobble is an ellipse or circle, then correction is needed. Usually advancing.
Ok, bear with me: HOW, exactly, does one adjust the phase? It's not clear if this is something in the radio, the BeastX or the mechanical setup. I've never run across such an adjustment in any of the manuals for these three systems(radio, BeastX or heli).
ehernan3 is offline        Reply With Quote
Old 07-24-2012, 01:47 AM   #18
kimmik
Registered Users
 
My HF Map location
Join Date: Sep 2011
Location: Australia
Default

Skookum has a setting. It's a fbl adjustment. Vbar too I'm sure, no
kimmik is offline        Reply With Quote
Old 07-24-2012, 01:48 AM   #19
kimmik
Registered Users
 
My HF Map location
Join Date: Sep 2011
Location: Australia
Default

Not sure about 3gx or bx
kimmik is offline        Reply With Quote
Old 07-24-2012, 02:02 AM   #20
gothicbunny
Registered Users
 
Posts: 2,899
 
My HF Map location
Join Date: Mar 2010
Location: Winnipeg, MB
Default

With the beastx you can adjust the phase with the micro settings software. You will need the USB adapter.
__________________
Don Newman - Team Pilot for Loving Girlfriend
MAAC #82859 - Align 250 Pro DFC, Align 550E DFC, VWINRC 550 FBL
gothicbunny is offline        Reply With Quote
Reply




Unregistered
Go Back   HeliFreak > R/C Helicopters > Aerodynamics, Physics and Engineering


Aerodynamics, Physics and Engineering Aerodynamics, Physics and Engineering Discussions

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Copyright © 2004-2011 - William James - Helifreak.com