Trex600 Nitro Pro Build Vids - Page 32

Finless · 09-16-2011, 10:51 AM

You should post these kinds of questions in the forum for the heli. The Trex Nitro forum is here:
http://www.helifreak.com/forumdisplay.php?f=78

However. First it is odd you have a Nitro with the old plastic tail case. I do not recall Align ever making a Nitro version with that tail case?
But for that old plastic tail case, the pitch slider control arm is VERY close to the case. It will rub the case if you forget to put in the spacer washer between the bell crank and the arm the bell crank pivots on. It was common back then users would either forget this spacer washer or put the wrong washer there (a thinner one). If the arm is rubbing and the thick spacer washer is there then usually it was due to a warped plastic arm.

Bob

Ger2010 · 01-08-2012, 06:13 AM

Hi Bob.
Thankyou for your vids. Excelent.
I need some help in this set up. Do you have a video or link to see how to set up these Align Gov in the T-Rex600NFBL with the 10C Futaba radio + 8 Channel Fasst Receiver?.
Thank you.
Ger

ginnethone · 01-13-2012, 03:56 AM

Bob, do you have video of GY701 using DX7 transmitter?

jogarce

Finless · 01-14-2012, 11:11 AM

See my Trex 500 nitro conversion videos and I show how to setup the Align gov. It's not with a Futaba radio thought but the principles are the same.

I have not done a GY701 but John has:
http://www.helifreak.com/showthread.php?t=252108

Bob

chase boy 301 · 01-22-2012, 02:23 PM

helps out a lot bob thanks

chase boy 301 · 01-22-2012, 02:29 PM

excellent job Bob helps out a lot for my first time with my new hoobby

cliff600 · 02-13-2012, 04:36 PM

On the GV1 setup you said it could be adjusted in the adj. travel...I can do it when I am in the programming part, but it does not seem to change if I am flying it. Is that normal or am I doing something wrong.

I have one other question.....I also have a .90 size Raptor.....where should the RPM's be for the three flight modes? I set it up like the .50, but that seems to be insanely too much RPM's.

lazsyss350 · 03-01-2012, 12:27 AM

hey bob, Im have a little trouble setting up my cy atg on my 9303, do you have by chance a tutorial on how you would set it up on a 9303.

jase88 · 07-12-2012, 07:29 PM

hi bob or any one please reply back i can fly a rc heli but i did not assemble my raptor 30 now i have bought a new raptor 30 to assemble which i managed to assemble fine i really like the look of a t rex 600 v2 nitro limited edition would you say any one that can assemble a raptor 30 will not have problems assembling a t rex 600 because the Manuel makes it look hard to assemble is there any better manuals out there or would you recomend i just buy all quick uk parts to upgrade the raptor to anodised parts and forget about the t rex

smallmand · 07-14-2012, 02:47 PM

great build videos thanks a million

09-16-2011, 10:51 AM	#621
Finless Team Taco VP Thread Starter My HF Map location Join Date: Nov 2005 Location: Stanton, Ca. USA	You should post these kinds of questions in the forum for the heli. The Trex Nitro forum is here: http://www.helifreak.com/forumdisplay.php?f=78 However. First it is odd you have a Nitro with the old plastic tail case. I do not recall Align ever making a Nitro version with that tail case? But for that old plastic tail case, the pitch slider control arm is VERY close to the case. It will rub the case if you forget to put in the spacer washer between the bell crank and the arm the bell crank pivots on. It was common back then users would either forget this spacer washer or put the wrong washer there (a thinner one). If the arm is rubbing and the thick spacer washer is there then usually it was due to a warped plastic arm. Bob __________________ "Don't Taco My Pack Dude!" To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. *To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.* *To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.* *To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.* *To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.*

01-08-2012, 06:13 AM	#622
Ger2010 Registered Users Join Date: Dec 2010 Location: Bolivia, Cochabamba, Cochabamba.	Align GOV set up video Hi Bob. Thankyou for your vids. Excelent. I need some help in this set up. Do you have a video or link to see how to set up these Align Gov in the T-Rex600NFBL with the 10C Futaba radio + 8 Channel Fasst Receiver?. Thank you. Ger

01-14-2012, 11:11 AM	#624
Finless Team Taco VP Thread Starter My HF Map location Join Date: Nov 2005 Location: Stanton, Ca. USA	See my Trex 500 nitro conversion videos and I show how to setup the Align gov. It's not with a Futaba radio thought but the principles are the same. I have not done a GY701 but John has: http://www.helifreak.com/showthread.php?t=252108 Bob __________________ "Don't Taco My Pack Dude!" To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. *To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.* *To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.* *To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.* *To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.*

02-13-2012, 04:36 PM	#627
cliff600 Registered Users Join Date: Nov 2005 Location: Palmyra, Va.	On the GV1 setup you said it could be adjusted in the adj. travel...I can do it when I am in the programming part, but it does not seem to change if I am flying it. Is that normal or am I doing something wrong. I have one other question.....I also have a .90 size Raptor.....where should the RPM's be for the three flight modes? I set it up like the .50, but that seems to be insanely too much RPM's. __________________ Where does the white go when the snow melts?

07-12-2012, 07:29 PM	#629
jase88 Registered Users Join Date: Jun 2012 Location: united kingdom	raptor 30 or t rex 600 v2 nitro hi bob or any one please reply back i can fly a rc heli but i did not assemble my raptor 30 now i have bought a new raptor 30 to assemble which i managed to assemble fine i really like the look of a t rex 600 v2 nitro limited edition would you say any one that can assemble a raptor 30 will not have problems assembling a t rex 600 because the Manuel makes it look hard to assemble is there any better manuals out there or would you recomend i just buy all quick uk parts to upgrade the raptor to anodised parts and forget about the t rex

01-13-2012, 03:56 AM	#623
ginnethone Registered Users Join Date: May 2009 Location: philippines	Bob, do you have video of GY701 using DX7 transmitter? jogarce

01-22-2012, 02:23 PM	#625
chase boy 301 Registered Users Join Date: Jan 2012 Location: MD	helps out a lot bob thanks

01-22-2012, 02:29 PM	#626
chase boy 301 Registered Users Join Date: Jan 2012 Location: MD	excellent job Bob helps out a lot for my first time with my new hoobby

03-01-2012, 12:27 AM	#628
lazsyss350 Registered Users Join Date: Mar 2009 Location: Arlington hts, IL	hey bob, Im have a little trouble setting up my cy atg on my 9303, do you have by chance a tutorial on how you would set it up on a 9303.

07-14-2012, 02:47 PM	#630
smallmand Registered Users Join Date: Apr 2012 Location: canada	awesome great build videos thanks a million

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode