atv swash giving a headache

[jaeger]

Re building after ground attack its been awhile 9 months since last set up I am doing every thing right center sticks 90 degree servo horns level swash at mid stick, but when high and low stick atvs arent doing a thing I ve been at this for 17hrs straight and I am going mental I ve read the threads etc but something not happening any pointers thank you

[Larry227]

So when you go to level the swash at low/high stick adjusting the atv's don't move the servos at all? That's odd. Were they damaged in the crash? It's been a long time since I setup from scratch too so maybe it's just something simple and I can't think of it either.

[jaeger]

These are my settings re bind radio to heli, what ive just found was while adjusting swash at high and low stick to get atvs to work had to jiggle appropriate stick to make atv respond is this a dx6i glitch 24 hrs just figure that out
D/R & Expo
Aile - 0 - 100% 1 - 100% INH
Elev - 0 - 100% 1 - 100% INH
Rudd - 0 - 100% 1 - 100% INH

Travel Adj (all percentages are in both directions)
Thr - 100%
Ail - 100%
Ele - 100%
Rud - 100%
Gyro - 100%
Pitch - 100%

Sub Trim
Thro 0 Aile 0
Elev 0 Rudd 0
Gyro 0 Pitch v34

Gyro
SW-Gyro Pos 0: 25% Pos 1: 77.0%

THR Curve
Normal: L - 0% / 2 – 50% / 3 - 80% / 4 - 90% / H - 100%
Stunt: L - 100% / 2 - 95% / 3 - 90% / 4 - 95% / H - 100%
Hold - 0.0%

Pitch Curve
Normal: L - 40% / 2 - 45% / 3 - 50% / 4 - 75% / H - 100%
Stunt: L - 0% / 2 - 25% / 3 - 50% / 4 - 75% / H - 100%
Hold: L - 40% / 2 - 45% / 3 - 50% / 4 - 75% / H - 100%

Swash Mix
Aileron - +60% (positive)
Elevator - +60% (positive)
Pitch - +71% (positive) BLADE GRIP FLIP

Mix 1 & 2 are INH'd

Revo Mix
Norm - 0% Up & Down
Stunt - 0% Up & Down

Reverse
Thro-N Aile-R
Elev-N Rudd-N
Gyro-N Pitch-N

SWASH TYPE
CCPM 120

[Larry227]

I don't remember if that was one of the glitches that was happening on these or not but it wouldn't hurt to check if your DX6i is on the recall list from last year.
http://www.spektrumrc.com/Articles/A...ArticleID=1901

There's one thing you could try. Copy your model to a blank model and then bind to that new one and see if the glitch is there too.

[Dazhim]

Jus tossin out there.. have u tried movin the values past 100%

[Wiggen]

This is the way this radio works.
To level the swash at low/hi end,just go to the atv/traveladjust. screen.Hold the cyclic stick in the desired direction and at the same time scroll the wheel.If the swashplate isn,t moving or moving in wrong direction just push the stick in the opposite direction and scroll.

[jaeger]

Checked radio numbers its not a dud, wiggling the stick seemed to wake up the servos,had the beast hovering over the deck tonight -1.6c out side, I cant stand it when I get beaten and doing extended hours to get it flying again has fried my brain. This rebuild was a mission to sort out thanks every one for replys. Now time to sleep