Step G still not sure how to save properly

bladesr · 07-15-2012, 12:13 PM

Should I leave Step G at one of the servos (with light on ) or at reference point (light off ) or it doesn't matter ??? thanks !

newbheliusr · 07-15-2012, 12:20 PM

Doesn't matter

Sent from my iPhone using Tapatalk

sutty · 07-15-2012, 12:35 PM

+1, it doesn't matter. This having been said, there is a small advantage with moving on whilst one of the servo lights is on. This way you can definitely see that you are moving on whilst all the servos are in their adjusted positions. If you had missed one it would be obvious. Since all will be out, to some extent, when in the reference position, and all will move to the adjusted positions when you press the button to move on, it perhaps isn't so obvious if one has been missed. Or maybe it would still be obvious.

I assume you have a reason for asking? Are you having some trouble getting it to store the changes you make at G?

Cheers

Sutty

bladesr · 07-15-2012, 01:42 PM

To Sutty, no I don't think I have any problem in saving but just want to make sure since I am flying a 700 and try to be 100% sure for everything . I had seen many different opinion on this matter , I looked in the manual it didn't mention or the setups videos same thing. The more I read the forum the more I get worry , you know what I mean !! Regards.

sutty · 07-15-2012, 02:04 PM

If you have some worry, and I can undersand that for a 700, then simply look at J. When you go into J, if it starts at 0 on the blades, and your servo arms are square, or where you need them to be, like you set-up at G, then you know you did everything right, because J uses the same starting position as saved at G, in other words the elctronically adjusted centres.

You can also triple check by putting your radio at mid stick, in throttle hold, or with motor disconnected, and see if you get the same there as well. It should be at least very close, depending on the calibration of your radio.

The more you read the more you worry, well stop reading then, lol. Kidding of course, but if you have done a lot of reading then you will be better placed to understand all the potential issues, so you should worry less.

Good luck with the maiden.

Cheers

Sutty

bladesr · 07-15-2012, 02:50 PM

To Sutty ,
I think I did all the those steps you mentioned correctly It is for only the last part of the Step G I always thought each time I move a servo when in servo mode it is set at that position automatically , so I never think of when is the right position ( lights on / off) to leave Step G in order to save settings.

Regards
Anthony.

07-15-2012, 12:13 PM	#1
bladesr Registered Users Join Date: Jan 2011 Location: Vancouver Canada	Step G still not sure how to save properly Should I leave Step G at one of the servos (with light on ) or at reference point (light off ) or it doesn't matter ??? thanks ! __________________ Trex450Pro BeastX Trex550E HC3SX Trex700E HC3SX JR11X

07-15-2012, 12:20 PM	#2
newbheliusr Registered Users Join Date: Apr 2011 Location: Mountlake Terrace, Wa	Doesn't matter Sent from my iPhone using Tapatalk __________________ Heli's I've had:MCX2, MSR, HB FP V2, Blade SR, 120SR, Trex 250, Trex 450 sport, MCPX, Heli's I have: Trex 450 pro FBL BeastX (Clone Mostly Align), Gaui X5(SK540), X7(Vbar)

07-15-2012, 12:35 PM	#3
sutty Registered Users My HF Map location Join Date: Feb 2008 Location: Manchester, England	+1, it doesn't matter. This having been said, there is a small advantage with moving on whilst one of the servo lights is on. This way you can definitely see that you are moving on whilst all the servos are in their adjusted positions. If you had missed one it would be obvious. Since all will be out, to some extent, when in the reference position, and all will move to the adjusted positions when you press the button to move on, it perhaps isn't so obvious if one has been missed. Or maybe it would still be obvious. I assume you have a reason for asking? Are you having some trouble getting it to store the changes you make at G? Cheers Sutty __________________ Regards, Sutty BeltEXI, mCX, mSR, 4G3, FBL Trex250SE µB, FBL Trex450Pro µB, FBL Trex550e VX1, FBL Trex600ESP µB, Parkzone P51D

07-15-2012, 01:42 PM	#4
bladesr Registered Users Thread Starter Join Date: Jan 2011 Location: Vancouver Canada	To Sutty, no I don't think I have any problem in saving but just want to make sure since I am flying a 700 and try to be 100% sure for everything . I had seen many different opinion on this matter , I looked in the manual it didn't mention or the setups videos same thing. The more I read the forum the more I get worry , you know what I mean !! Regards. __________________ Trex450Pro BeastX Trex550E HC3SX Trex700E HC3SX JR11X

07-15-2012, 02:04 PM	#5
sutty Registered Users My HF Map location Join Date: Feb 2008 Location: Manchester, England	If you have some worry, and I can undersand that for a 700, then simply look at J. When you go into J, if it starts at 0 on the blades, and your servo arms are square, or where you need them to be, like you set-up at G, then you know you did everything right, because J uses the same starting position as saved at G, in other words the elctronically adjusted centres. You can also triple check by putting your radio at mid stick, in throttle hold, or with motor disconnected, and see if you get the same there as well. It should be at least very close, depending on the calibration of your radio. The more you read the more you worry, well stop reading then, lol. Kidding of course, but if you have done a lot of reading then you will be better placed to understand all the potential issues, so you should worry less. Good luck with the maiden. Cheers Sutty __________________ Regards, Sutty BeltEXI, mCX, mSR, 4G3, FBL Trex250SE µB, FBL Trex450Pro µB, FBL Trex550e VX1, FBL Trex600ESP µB, Parkzone P51D

07-15-2012, 02:50 PM	#6
bladesr Registered Users Thread Starter Join Date: Jan 2011 Location: Vancouver Canada	To Sutty , I think I did all the those steps you mentioned correctly It is for only the last part of the Step G I always thought each time I move a servo when in servo mode it is set at that position automatically , so I never think of when is the right position ( lights on / off) to leave Step G in order to save settings. Regards Anthony. __________________ Trex450Pro BeastX Trex550E HC3SX Trex700E HC3SX JR11X

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode