 |
START HERE |
|
| Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
|
|
|
Unregistered
|
||||||
| Align 3G FBL System Align 3G FBL Flybarless System Software and Hardware Support |
|
|
 |
|
|
LinkBack | Thread Tools | Display Modes |
10-30-2010, 01:48 AM
|
#1 (permalink) |
|
Registered Users
Join Date: Apr 2010
|
Crappy 3G Connector
So after my 500 dove into the dirt the other day I ruled it out as my connection vibrating out of the main 3G unit. With the USB interface out now, we plug these things in and out alot when setting it up. After the first one or two times I disconnected the thing it never made a good connection again. Just tapping on it a certain way causes it to reboot. I know this is a common complaint and was wondering what everyone is doing to solve this issue??
__________________
-Goblin 700: Crashed but re-building, still needing electronics  -Goblin 630: CC Ice 120HV, vBar Last edited by DominicD; 10-30-2010 at 05:32 AM.. Reason: Poor choice of words in the topic |
|
|
| Sponsored Links | |||
|
Advertisement |
|
||
|
10-30-2010, 01:51 AM
|
#2 (permalink) |
|
Registered Users
|
I agree the connector is not the greatest. Are you removing it properly?
Also I think it is best to let the Y cable installed and of course all connections should be shoo gooped especially on the 3-G unit which seems to vary greatly in tolerances. |
|
|
|
|
10-30-2010, 01:53 AM
|
#3 (permalink) |
|
Registered Users
|
Same happened to me with my 700. I chalked it up as my own fault for failing to make sure the connections were solid during my pre-flight. I just hooked up the 3g link cable the night before and I remember having problems plugging it in. I was lucky and just killed a few tail gears.
I will never have that problem again as I have taken some extra precautions.
__________________
-Joe "Helis - wallet weight reduction made easy" HeliArt Jskrapper @ youtube |
|
|
|
|
10-30-2010, 05:10 AM
|
#4 (permalink) |
|
Registered Users
Join Date: Mar 2010
|
It may be the pins on the sensor have been pushed in making a bad connection.
The later models now have expoxy behind them to stop this happening. There is a sticky regarding this issue. Have you done the mod? If not, while you have the sensor open, glue the pins to hold them in place.
__________________
Compass 6HV, TotalG, BLS251, DX7S. Kasama Srimok, Scorpion HK-4525-520KV, TotalG, BLS251, DX7S. ...and the rest... |
|
|
|
|
10-30-2010, 05:33 AM
|
#5 (permalink) |
|
The Capi
|
I edited the thread title, please don't subvert the language filters.
__________________
Spreading capibara awareness since 2006 |
|
|
|
|
10-30-2010, 11:33 AM
|
#6 (permalink) | |
|
Registered Users
Thread Starter
Join Date: Apr 2010
|
Quote:
__________________
-Goblin 700: Crashed but re-building, still needing electronics -Goblin 630: CC Ice 120HV, vBar |
|
|
|
|
|
11-02-2010, 11:31 PM
|
#7 (permalink) |
|
Registered Users
Join Date: Jun 2010
|
mine does a reboot if i move the wire,but if i have th eY harness on iot doesnt reboot
__________________
Trex 700E DFC V-Bar , Trex 600N , Logo 600 SE FBL V-bar, Logo 600/550 FBL V-bar,Logo 400 FBL V-Bar ,Goblin 500 V-Bar, Blade 130X , Blade MCPx , Blade 500X |
|
|
|
|
|
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
| Display Modes | |
Linear Mode
|
|
