Register Now

carpo · 10-23-2009, 08:08 PM

i just finish puting the brushless tail motor to my 4#3 cause the old carbon motor was give me a erratic tail ...
and now that i have the new motor insataled the thail still a little inestable ...
when the thing came out of the box was solid as a rock ...and now with the main and the tail motor made to brushlees the tail its not lock on
any ideas

ps sorry about my english

Dusty1000 · 10-24-2009, 02:31 AM

Hi, which 4#3 do you have? Is it MHz or GHz?

Dusty

carpo · 10-25-2009, 06:13 PM

its the one that came with maun brussless motor ...and i buy it with the tail upgrade

carpo · 10-25-2009, 08:07 PM

its a rx2406a 2,4 ghz

i dont know haw to conect cause i get like a y that i can conect the esc of the tail and the main brushlles motor and also i have the power of the trasmiter
i have 400 batery ..its ok to conect 2 of them one to the esc with the y and one to the receiver?

Dusty1000 · 10-26-2009, 02:26 AM

Unfortunately there have been several reports of gyros not working well on the RX2406A. The older 2406 and newer 2406B don't have this problem.

Connecting 2 batteries would make the heli too heavy for starters. You could wire the power cables from the esc and 4 in 1 together and connect them to a single battery, though I doubt you would notice any difference.

Something else I've just thought of, make sure the 4 in 1 is well stuck on it's double sided sticky pad - if it is at all loose, this can cause tail problems

Dusty

10-23-2009, 08:08 PM	#1 (permalink)
carpo Registered Users My HF Map location Join Date: Sep 2007	gyro not lock on i just finish puting the brushless tail motor to my 4#3 cause the old carbon motor was give me a erratic tail ... and now that i have the new motor insataled the thail still a little inestable ... when the thing came out of the box was solid as a rock ...and now with the main and the tail motor made to brushlees the tail its not lock on any ideas ps sorry about my english

10-24-2009, 02:31 AM	#2 (permalink)
Dusty1000 Registered Users Join Date: Sep 2008	Hi, which 4#3 do you have? Is it MHz or GHz? Dusty __________________ Blade 400, mSR, mCPX - Sonix SX450SE - Walkera 1#A, 4#3, 4#3A, 4#3B, 4G3

10-25-2009, 06:13 PM	#3 (permalink)
carpo Registered Users Thread Starter My HF Map location Join Date: Sep 2007	its the one that came its the one that came with maun brussless motor ...and i buy it with the tail upgrade

10-25-2009, 08:07 PM	#4 (permalink)
carpo Registered Users Thread Starter My HF Map location Join Date: Sep 2007	hmm its a rx2406a 2,4 ghz i dont know haw to conect cause i get like a y that i can conect the esc of the tail and the main brushlles motor and also i have the power of the trasmiter i have 400 batery ..its ok to conect 2 of them one to the esc with the y and one to the receiver?

10-26-2009, 02:26 AM	#5 (permalink)
Dusty1000 Registered Users Join Date: Sep 2008	Unfortunately there have been several reports of gyros not working well on the RX2406A. The older 2406 and newer 2406B don't have this problem. Connecting 2 batteries would make the heli too heavy for starters. You could wire the power cables from the esc and 4 in 1 together and connect them to a single battery, though I doubt you would notice any difference. Something else I've just thought of, make sure the 4 in 1 is well stuck on it's double sided sticky pad - if it is at all loose, this can cause tail problems Dusty __________________ Blade 400, mSR, mCPX - Sonix SX450SE - Walkera 1#A, 4#3, 4#3A, 4#3B, 4G3 Last edited by Dusty1000; 10-26-2009 at 03:46 AM.. Reason: add info

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in