START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Castle Creations ESC and Software Castle Creations ESC Software and Hardware Support |
|
LinkBack | Thread Tools | Display Modes |
11-13-2013, 03:14 AM | #61 (permalink) |
Registered Users
Join Date: Sep 2009
|
Re: Castle Creations Quick Tip videos
Failsafe is the position of your transmitter sticks at time of binding, typically throttle all the way closed and cyclic neutral....
Sent from my DROID3 using Tapatalk 2
__________________
"It's not the crash so much as the sudden stop" Compass 7HV, Compass 6HV, TRex450Pro, bunch of other junk in boxes ... Team Flybar Team Tail-In wannabe.... |
Sponsored Links | |||
Advertisement |
|
03-08-2014, 05:44 PM | #62 (permalink) |
Registered Users
Join Date: Jan 2014
|
I am probably in over my head with this TREX 600 build, but I have somehow figured out every single piece of this heli except for this HV80. I having been trying to get the endpoints recognized for two days with no luck. I got the HV80 set up for Heli mode in the PC. Set radio to linear throttle/pitch with no trims, Dissabled thr cut. I then set the throttle endpoints to 30/30 and leave throttle stick at max. I turn on the receiver and see all servos responding correctly. Then I plug in the HV80 and get the 12 beeps as I expect. Then I start raising the endpoints in my radio and it goes to 140 without being recognized.
|
03-08-2014, 05:55 PM | #63 (permalink) |
Registered Users
Join Date: Oct 2010
|
Try reversing channel sound like u have a futaba radio ch needs to be reversed ... isnt working because when you plug it in at max it thinks its min ...
When you re do it with ch 3 reverse . After u set max then min you will get the chime that it armed ... hope that helps Sent from my SCH-I535 using Tapatalk |
03-09-2014, 10:19 AM | #64 (permalink) | |
Registered Users
Join Date: Jan 2014
|
Quote:
|
|
03-09-2014, 10:44 AM | #65 (permalink) |
Registered Users
Join Date: Jan 2014
|
The pamphlet that came with the HV80 says the red wire does NOT have to be removed for the Ice2 HV. Almost every vid I have seen says to disconnect the red wire if using an separate BEC. Go figure.
After reconnecting the red wire, When I did the end point adjustment the HV80 finally collected a high endpoint of 119. I added 2, then started to lower the throttle stick. At this point the motor spun up??? Do I need to clear the initialization somehow and redo this step. It would appear I need to put the throttle servo back to not-reversed? |
03-09-2014, 10:48 AM | #66 (permalink) |
Registered Users
Join Date: Jan 2014
|
One other question while I am thinking of it. I am assuming I should be doing this initialization in DIR setup for the 3GX? Once the throttle is finally set with its endpoints for the HV80 I would then go into the 3GX to set the throttle calibration?
|
02-10-2015, 05:10 PM | #67 (permalink) |
Registered Users
Join Date: Sep 2012
|
[QUOTE=nSidio;5701741]The pamphlet that came with the HV80 says the red wire does NOT have to be removed for the Ice2 HV. Almost every vid I have seen says to disconnect the red wire if using an separate BEC. Go figure.
/QUOTE] that's for speed controls that have a built in bec ... |
02-10-2015, 08:57 PM | #68 (permalink) |
Registered Users
Join Date: Oct 2010
|
Ice2 does not have a bec .. only cut IF your hooking up esc with internal bec ..
Did you get your end points figured out ? When you configure you end point . You take pinion off motor for safety End points low and linear as you describe Full throttle and plug battery in this put it in programing mode .. Set hi end point till bleep .. Lower and repeat bleep .. After that when u lift the stick it will begin to spool up .. |
04-30-2016, 04:46 PM | #69 (permalink) |
Registered Users
Join Date: Mar 2012
|
cc edge 50, need help
I cant get the esc to go into program mode, rx is a gpro
|
06-19-2017, 03:40 PM | #71 (permalink) |
Registered Users
Join Date: Jan 2017
Location: Northern VA
|
Weird. I can only view the videos on phone/tablet but not from a physical computer and I've tried 3 different ones.
__________________
Logo 550se || MSH Mini Protos Stretch || Oxy 4 325 || NCPS || DX8 G2 |
08-12-2017, 05:15 AM | #72 (permalink) | ||||
CHC Benefactor
Join Date: Feb 2006
Location: Singapore
|
I think it's a problem with the youtube encoding. I had problems on both mobile and pc browsers. Here they are again:
__________________
Playing with gravity one heli at a time Dancing with gravity one flight at a time |
||||
Thread Tools | |
Display Modes | |
|
|