SOLD BABY! CF BLADE 400 CF CNC HEAD & TAIL ALIGN CASE MANY PARTS

[727al]

Bird has never left my garage and has only had 1 1/2 batteries run on the frame for hover / trim testing (very stable for a 400)! I have 7 400's & Trex 450 so I didn't need this one to fly. Electronics are all OEM Blade 400 stuff (very cheap to repair or replace) This is a true RTF, if UPS doesn't knock it around too much you should be able to take it out of the nice Align case and fly it Immediately. The battery has been fully charged to 12.6V so all you'll have to do is put 4 AA in the TX and UP~UP & AWAY you go. But realistically I'd would check to make sure it is set up to your standards. It is presently set up with +6 degrees mid stick (#3 position) this is a nice mild setting for a beginner to hover and do some sport / pattern flying. I like a very responsive stick so you may want to crank some + Expo into it as I believe I've got it set at -30? As I said prior, what you see in the pics is what you get but since it's a little hard to see the small stuff I'll list all items below.

I will also be listing several Trex 450 se v2 with low budget electronics for the financial impaired folks so they can have fun also. Once you put all that Schmancy~Fancy GYRO~ESC / BEC stuff into one it out prices it for us poor folk. Oh yes, if your just stating off I'll be listing my Hi-Performance CX2 CF all CNC shortly also.

PAYMENT: Paypal or Money Order (USPS ONLY) all others will get rejected.
Shipping: You pay what I pay and I'll send it any way you want.

PARTS LIST:
1- Spotless Blade 400 / Carbon Fiber Frame full CNC main & tail assy.
1- Align carrying case
New> Blades, Paddles & tail rotors
1- Manual (used)
1- 11.1 3s OEM battery under 15 cycles (never used below 3.75 volts per cell) NO PUFF!
7- Sets new blades consisting of:
2- Sets Fiber
4- Sets Woodies for the CNC head (1-presently on bird)
1- Set Woodie for spare OEM head
1- New Canopy + OEM on frame
2- New Main Shafts
1- New flybar Seesaw Holder (OEM)
1- New Belt
1- New Tail boom
1- Pitch Gauge
1- New Main Gear
1- Used Main Gear
1- Used Gear Set
1- 2-3 cell balance charger w/ battery clips
1- 120V adapter (wall plug) for above charger
1- OEM Main Head assy (bent feather shaft)
1- New Feather Shaft (OEM) for above assy)
1- OEM tail assy (bent shaft)
1- Tail Gear jack shaft
1- Set tail blades (used)
1- Horizontal fin (OEM used)
1- Vertical Fin (OEM used)
1- Foam Blade Holder
1- DX6i LIKE NEW (no batteries) has been programmed for this bird.
1- Set (4) DX6i CNC trim switches (2 installed & other 2 for you to install if & when needed) very easy. Spektrum makes a mean TX but they had their heads up their butt when they invented those trim switches / THEY BREAK!!!! No, not from dropping it, just from normal use. CNC's are $30.00+ shipping if you can find them!

If I missed anything that you may see in the pictures (helicopter related) so let's not get ridiculous, then it's still yours.

Let's not forget a stock 400 shipped is over $500.00 > that would be ALL PLASTIC, no case no spare parts etc.

I'm asking $500.00 (obo) + shipping. Will ship Internationally to certain locations
If you don't want the TX (-$75.00) No the tx is not 4~sale separately.
If you don't want the nice Align Case (-$25.00) No the Case is not 4~sale separately.

LOW BALLERS are welcome, you just won't get a reply, but you never know when "Ole Al's" had a few too many and may take you up on it

[727al]

entered in error

[727al]

Bump!

[727al]

Let's move this BEAST!

[727al]

Economy can't be that bad, is it folks. I noticed a post for 2x 12s batteries for $1400.00

[727al]

OK, What's the problem? Why do I still own this Gem

[pezdragon]

I am curious as to what make of swash plate it has, with a rear facing guide pin?

bump

[RCTada]

Is this for trade as well or strictly for sale?

[Norseman1]

Hi Al

Let me know if you are willing to seperate the spare parts and power supply for the charger please. PM also sent.

[727al]

What all you lookin for? I've got 4X 400 with Boo-Ku parts. I also have 2 Trex 450 CF I need to unload before the holidays as I just bought 2X Trex 500's I flies & other for spare parts.

[Norseman1]

PM sent Al.

[RCTada]

Would be interested in an Ultimate AMR RTF?

[727al]

There are dozens of those types on THIS great SITE, SPEND YOUR $$ WITH THEM.
The whole point is to have an EconO Trex 450. Once you put all the upgraded , ON A BIRD, you're what to 5 - 600.00+. I'm talking about a BNF for under $400.00 and maybe even in a case. In this scenario one can be flying in a day or two and not have to save up pocket change for 6 months. If they still enjoy the hobby down the line then they have the option to upgrade. Yes, I have all the Gee~Wis stuff to build a $1000.00 bird but that eliminates the 8-5er trying to raise a family in these hard times. Let's re~cap > Want bells @ whistles, start surfing. Want to get in the air with Chump~Change, then send me a deposit and we'll build one, JUST FOR YOU!

[727al]

If you want to make me an offer, go ahead as I may consider it but I actually didn't want to divide it up just yet. I'll list it on Ebay and if then it doesn't sell, I'll get more desperate

Thanks & sorry for any confusion

[727al]

Electronics cost more then that!

[sheffman]

Hi
how much to ship to Australia without TX?
cheers

[727al]

I'll work on that later Lived in Melbourne for 1 year and flew for Ansett

[727al]

just bought a BNF 500 from Americas911 so this thing needs to vacate, Rapido!

[727al]

Moving onto Ebay

[727al]

190353950334 I gave you freaks first CRACK