Register Now

Mr.Gobler · 05-21-2013, 09:54 PM

Skool me on this, I can't wrap my head around this. And i want to get it setup so flips and rolls are faster.

I know how to change the setting in the ar7200 to option : transmitter, but what i don't know is what to change in the radio ? I have a DX7s

HELP PLEASE!!

wanderer56 · 05-21-2013, 10:33 PM

You would adjust your D/R and tail response. Check in the BX forum for more info. I'm on TX mode, but mine is set pretty good and haven't had to adjust much for my liking. That's kind of a gray area in the manual. Not much info on that.

youturnjason · 05-21-2013, 10:36 PM

Set the aileron and elevator travel to their max, I think its 125% on the dx7s, then you can tame it down with D/R if needed.

Mr.Gobler · 05-21-2013, 10:40 PM

yeah, I don't use dual rates.

Sent from my SGH-I747M using Tapatalk 2

Skidpad · 05-21-2013, 10:49 PM

Yes, change your atv's and it will flip & roll faster; a friend of mine just did this on his 600, and it's a different animal now. Your maximum travel limits will still be limited by your BeastX setup. The BeastX manual only briefly mentions all of this.

Mr.Gobler · 05-21-2013, 10:53 PM

Quote:

Originally Posted by Skidpad

Yes, change your atv's and it will flip & roll faster; a friend of mine just did this on his 600, and it's a different animal now. Your maximum travel limits will still be limited by your BeastX setup. The BeastX manual only briefly mentions all of this.

I'm sorry to say but what are atv's where are they on the dx7s?

Sent from my SGH-I747M using Tapatalk 2

Bob O · 05-21-2013, 10:57 PM

Servo Setup, page 17 of the manual.

Make sure to adjust each side of the channel equally.

kelseh · 05-21-2013, 11:06 PM

Just increase your servo travel in the servo menu for aileron and elevation. This will increase your roll rate. Do it a little at a time so it doesn't get way fast on you. This will not change your max travel limits saved in the beast. You do the same thing for increasing your piro rate by increasing your rudder travel.

Mr.Gobler · 05-21-2013, 11:19 PM

Quote:

Originally Posted by kelseh

Just increase your servo travel in the servo menu for aileron and elevation. This will increase your roll rate. Do it a little at a time so it doesn't get way fast on you. This will not change your max travel limits saved in the beast. You do the same thing for increasing your piro rate by increasing your rudder travel.

This ?

to aileron & Eli? from 100 to 125 ? ( 125% is max.. )

Mr.Gobler · 05-22-2013, 09:42 AM

Or this ? Should i leave it at 100% and then try it ?

Dejavu*Xion · 05-22-2013, 01:38 PM

Leave your dual rates at 100%...Dont use any expo...Go to "servo setup " under "travel" start with 110% on your Aileron and elevator..From there work your way up in numbers untill you find your sweet spot.

Mr.Gobler · 05-22-2013, 02:57 PM

Quote:

Originally Posted by Goblin551

Leave your dual rates at 100%...Dont use any expo...Go to "servo setup " under "travel" start with 110% on your Aileron and elevator..From there work your way up in numbers untill you find your sweet spot.

what happens if i use a bit of expo ? Anything bad ? i use 10% expo on all 3 ali elv rud..

Skidpad · 05-22-2013, 03:34 PM

No, nothing bad will happen - its entirely a personal preference to achieve a desired feel through the sticks. Some use it, some don't, and there's no "right" or "wrong" here. The BeastX even allows for a small amount of additional expo when using one of the pre-programmed control behavior modes

DCflyer · 05-22-2013, 03:36 PM

Nothing bad will happen. Expo merely makes the heli less sensitive to inputs around center stick. This makes for easier landing and takeoff as well as smooth transitions in flight.

Mr.Gobler · 05-22-2013, 03:42 PM

Quote:

Originally Posted by DCflyer

Nothing bad will happen. Expo merely makes the heli less sensitive to inputs around center stick. This makes for easier landing and takeoff as well as smooth transitions in flight.

thats exatly why i use it, around center stick im a bit twitchy, i'm getting better and better, but for the time being, i like a little bit more expo

Thanks for all your help guys

Dejavu*Xion · 05-22-2013, 06:25 PM

Awsome...Glad you got it all figured out.

I sometimes forget that some people use expo on a fbl model. I have all 3 of mine set for - 15 ...........To many days of flying fb i guess.

Mr.Gobler · 05-22-2013, 07:38 PM

Quote:

Originally Posted by Goblin551

Awsome...Glad you got it all figured out.

I sometimes forget that some people use expo on a fbl model. I have all 3 of mine set for - 15 ...........To many days of flying fb i guess.

Programmed it today, will test on sunday when it's not raining and im not swamped at work!!

Hope all goes well LOL !!

youturnjason · 05-22-2013, 09:54 PM

If you set the travels to 125% then you can set Dual Rates to 80% which would be the same as 100% travel, so you can switch back and forth between both sensitivities.

Mr.Gobler · 05-22-2013, 10:06 PM

Quote:

Originally Posted by youturnjason

If you set the travels to 125% then you can set Dual Rates to 80% which would be the same as 100% travel, so you can switch back and forth between both sensitivities.

I'll try what i have setup first, then try you're suggestion after

05-21-2013, 09:54 PM	#1 (permalink)
Mr.Gobler Registered Users Join Date: Dec 2007	AR7200 parameter Menu B Skool me on this, I can't wrap my head around this. And i want to get it setup so flips and rolls are faster. I know how to change the setting in the ar7200 to option : transmitter, but what i don't know is what to change in the radio ? I have a DX7s HELP PLEASE!! __________________ ------------------------------------------------------------------------------------ http://www.alignrccdn.com/

05-21-2013, 10:33 PM	#2 (permalink)
wanderer56 Registered Users My HF Map location Join Date: Oct 2009	You would adjust your D/R and tail response. Check in the BX forum for more info. I'm on TX mode, but mine is set pretty good and haven't had to adjust much for my liking. That's kind of a gray area in the manual. Not much info on that. __________________ Trex 500-3226-1600, 14T, Koby 90LV, HS-5245MG, DS655, AR7200BX, DFC Trex 450 Sport-2221-8, 15T, CC Edge 50 Lite, HS-5065MG, HSG-5084MG, AR7200BX, DFC DX8

05-21-2013, 10:40 PM	#4 (permalink)
Mr.Gobler Registered Users Thread Starter Join Date: Dec 2007	Re: AR7200 parameter Menu B yeah, I don't use dual rates. Sent from my SGH-I747M using Tapatalk 2 __________________ ------------------------------------------------------------------------------------ http://www.alignrccdn.com/

05-21-2013, 10:49 PM	#5 (permalink)
Skidpad Registered Users Join Date: Jan 2012	Yes, change your atv's and it will flip & roll faster; a friend of mine just did this on his 600, and it's a different animal now. Your maximum travel limits will still be limited by your BeastX setup. The BeastX manual only briefly mentions all of this. __________________ 180CFX, Trex 550E (night), Goblin 570, Goblin 630C, DX8

05-21-2013, 10:57 PM	#7 (permalink)
Bob O Member My HF Map location Join Date: Dec 2008	Servo Setup, page 17 of the manual. Make sure to adjust each side of the channel equally. __________________ ):>

05-21-2013, 10:36 PM	#3 (permalink)
youturnjason Registered Users Join Date: Apr 2012	Set the aileron and elevator travel to their max, I think its 125% on the dx7s, then you can tame it down with D/R if needed.

05-21-2013, 11:06 PM	#8 (permalink)
kelseh Registered Users Join Date: May 2010	Just increase your servo travel in the servo menu for aileron and elevation. This will increase your roll rate. Do it a little at a time so it doesn't get way fast on you. This will not change your max travel limits saved in the beast. You do the same thing for increasing your piro rate by increasing your rudder travel. __________________ Blade 550x, Atom 500 FBL, Trex 450 Pro FBL, DX8

05-22-2013, 09:42 AM	#10 (permalink)
Mr.Gobler Registered Users Thread Starter Join Date: Dec 2007	Or this ? Should i leave it at 100% and then try it ? __________________ ------------------------------------------------------------------------------------ http://www.alignrccdn.com/

05-22-2013, 01:38 PM	#11 (permalink)
Dejavu*Xion Registered Users Join Date: Dec 2012	Leave your dual rates at 100%...Dont use any expo...Go to "servo setup " under "travel" start with 110% on your Aileron and elevator..From there work your way up in numbers untill you find your sweet spot.

05-22-2013, 03:34 PM	#13 (permalink)
Skidpad Registered Users Join Date: Jan 2012	Re: AR7200 parameter Menu B No, nothing bad will happen - its entirely a personal preference to achieve a desired feel through the sticks. Some use it, some don't, and there's no "right" or "wrong" here. The BeastX even allows for a small amount of additional expo when using one of the pre-programmed control behavior modes __________________ 180CFX, Trex 550E (night), Goblin 570, Goblin 630C, DX8

05-22-2013, 03:36 PM	#14 (permalink)
DCflyer Registered Users Join Date: Jan 2013 Location: DC	Nothing bad will happen. Expo merely makes the heli less sensitive to inputs around center stick. This makes for easier landing and takeoff as well as smooth transitions in flight. __________________ OXY5 MEG / 12S RAW KSE / 14S TDSF / 6S OXY rep

05-22-2013, 06:25 PM	#16 (permalink)
Dejavu*Xion Registered Users Join Date: Dec 2012	Awsome...Glad you got it all figured out. I sometimes forget that some people use expo on a fbl model. I have all 3 of mine set for - 15 ...........To many days of flying fb i guess.

05-22-2013, 09:54 PM	#18 (permalink)
youturnjason Registered Users Join Date: Apr 2012	If you set the travels to 125% then you can set Dual Rates to 80% which would be the same as 100% travel, so you can switch back and forth between both sensitivities.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in