START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
HobbyWing ESC's HobbyWing ESC Support |
|
LinkBack | Thread Tools | Display Modes |
12-01-2011, 07:18 AM | #1 (permalink) |
Registered Users
Join Date: Dec 2008
|
Idle 1 and 2 not work
Hi, I put im trex 550 HW 100A , when I change from normal to ST1 or ST2 not change
the RPM. I verify evrithing in the radio and all look fine. I use DX7. I use in normal 75 % flat ST 1 90% flat ST 2 95% flat Pls if you have idea wwhat is the problem let me know. Thanks,Luis |
Sponsored Links | |||
Advertisement |
|
12-01-2011, 07:27 AM | #2 (permalink) |
Registered Users
Join Date: Jun 2011
|
Make sure your end points are set correct in the ESC. You have to program them before you set your idle one and two.
In normal mode set your tx to 100 in throttle curve on the top point, and 0 on the bottom point. Then go to you ESC program and set it in there. At this point the ESC will see the actual top and bottom of the left stick. Then adjust your Norm, idle 1 and 2 according to your desired Head Speed I had the sane issue, common overlook. Sent from my Droid Charge using Tapatalk. |
12-01-2011, 07:31 AM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Dec 2008
|
My endpoints in the radio are 100%
|
12-01-2011, 10:56 AM | #5 (permalink) |
Registered Users
Join Date: Jun 2011
|
See this thread i started a few months back..
https://www.helifreak.com/showthread.php?t=344199 Sent from my Droid Charge using Tapatalk. |
12-01-2011, 04:31 PM | #6 (permalink) |
Registered Users
Thread Starter
Join Date: Dec 2008
|
How I reprogram the esc?
|
12-03-2011, 01:25 AM | #8 (permalink) |
Registered Users
Join Date: Mar 2011
|
i think this is where i screwed up so what u are saying is set esc to default change throttle curve to liner line 0 25 50 75 100 in normal idle 1 idle 2 program your esc and governer mode after thats done change idle 1 or 2 to flat 80 or 100
|
12-03-2011, 09:00 AM | #9 (permalink) | |
Registered Users
Join Date: Jun 2011
|
Quote:
One thing that threw me was you need to have throttle hold "armed" so the TX transmits the signal. Sent from my Droid Charge using Tapatalk. |
|
12-03-2011, 11:41 PM | #10 (permalink) | |
Registered Users
Join Date: Mar 2011
|
Quote:
__________________
BLACKOUT MINI,ZMR 250,TBS Discovery ,Zephyr 2 TARANIS X9D + ,ez-uhf jr mod GauiX5 Gauix3 |
|
12-04-2011, 08:56 AM | #11 (permalink) | |
Registered Users
Join Date: Jun 2011
|
Quote:
When you program the ESC make sure you have 2 motor wires unplugged, or take tail and rotor blades off. Even though programming mode does not arm the motor, it is better safe than sorry. Sent from my Droid Charge using Tapatalk. |
|
12-04-2011, 06:12 PM | #12 (permalink) |
Registered Users
|
No, hold needs to be off.
__________________
Compass 3D+ - OS55 Hyper/Hatori/Vbar
Atom 500 Tarot 450 Pro - AR7200BX Spektrum DX8 |
12-05-2011, 03:23 AM | #14 (permalink) |
Registered Users
Join Date: Jan 2010
|
I had the same problem before I had to redo my throttle end points in ESC and then it was good.
Just make sure before you redo your end points in ESC have a linear throttle and pitch curves and in travel adjust have +/-100 I had my throttle hold at 0 then adjusted where throttle hold works. Cheers Sent from my iPhone using Tapatalk
__________________
Trex 600E Pro FBL with V-bar,600MX-510KV,HW 70A HV ESC, CC BEC Pro,Align DS610,Futaba BLS251, JR11X with Hyperion LifePO4, Icharger 306B with Meanwell 1000W 24v power supply. |
Thread Tools | |
Display Modes | |
|
|