Register Now

427notch · 07-02-2011, 03:36 AM

I got everything I needed and rebuilt the CopTrerX again.
I have the stock cx-ct6a radio with cx-96a reciver and fresh t-pro servos.
I got the heli set up then checked and adjused the servos then pulled all the electroics and installed Flymentor , After a long time of plug and play because something's are not the same but I can tilt the heli to the right ,left ,back,forward and have no responce from the servos for the head.
I am at a end the cost of a new tx and rx vs a 2.4GHz BlueRay 450PE 3D Brushless RC Helicopter RTF or HeliPro Black Hawk 450 SE 6 CH CCPM 3D Aerobatic R/C Electric Helicopter RTF .I dont care any thing about 3-d I just want my grandson to see something other than a pile of parts in my floor. Any idea what I have wrong.
I have downloaded the t6config.exe program but it does not seem to help.

Copter64 · 07-02-2011, 07:54 AM

I'm not familiar with that particular helicopter, but....I noticed you mentioned some other software but did not mention "HeliBal" (the software that is used to configure the Flymentor). What does that software show as its settings?
What is the light on the KDS flymentor doing? (solid green, solid red, flashing red, etc?)

shibby75 · 07-02-2011, 01:36 PM

Have you set your tx to a single servo swash setup?

427notch · 07-02-2011, 02:00 PM

I set the tx to Heli- 90 and I have the programer for the Flymentor.
The heli is a Copterx with about 80% of the parts beong Align t-rex.
The light does go to solid green.

Ivor Hill · 07-02-2011, 03:14 PM

Are the servos plugged in the correct way, signal wire closest to the port numbers ?.
Is the FM gyro plugged in the correct way ?.
Is there any movement when you operate the sticks.
Connect the servo back into your reciever and operate the sticks. Throttle shoud move 1 servo, elevator another servo and aileron the third servo.

427notch · 07-02-2011, 04:08 PM

The tx is not staying on heli-90 it keeps going back to acro.
When first hooked it up the motor would not work then I had to plug and play everything to get the controler to work right but my tx is not keeping the heli-90 settings after I take it off the pc. I think im going to have to upgrade the 4 year old radio system to make everything work right.

Jerry Campbell · 07-02-2011, 05:40 PM

I also have a T6 transmitter with the t6config software and there is no choice for a single servo. I have a new transmitter on the way. I'm sure you will have to do the same thing.
Good luck
Jerry

07-02-2011, 03:36 AM	#1 (permalink)
427notch Registered Users Join Date: Jun 2011	Flymentor Help I got everything I needed and rebuilt the CopTrerX again. I have the stock cx-ct6a radio with cx-96a reciver and fresh t-pro servos. I got the heli set up then checked and adjused the servos then pulled all the electroics and installed Flymentor , After a long time of plug and play because something's are not the same but I can tilt the heli to the right ,left ,back,forward and have no responce from the servos for the head. I am at a end the cost of a new tx and rx vs a 2.4GHz BlueRay 450PE 3D Brushless RC Helicopter RTF or HeliPro Black Hawk 450 SE 6 CH CCPM 3D Aerobatic R/C Electric Helicopter RTF .I dont care any thing about 3-d I just want my grandson to see something other than a pile of parts in my floor. Any idea what I have wrong. I have downloaded the t6config.exe program but it does not seem to help. Last edited by 427notch; 07-02-2011 at 05:24 AM..

07-02-2011, 07:54 AM	#2 (permalink)
Copter64 Registered Users Join Date: Jan 2011	I'm not familiar with that particular helicopter, but....I noticed you mentioned some other software but did not mention "HeliBal" (the software that is used to configure the Flymentor). What does that software show as its settings? What is the light on the KDS flymentor doing? (solid green, solid red, flashing red, etc?) __________________ Blade mSR; ClearView R/C Simulator; Blade mCP-x; HK-450-Pro (Belt tail) YouTube channel: ResponsibleCitizen64 Latest videos: Turnigy Flybarless 600 system on a HK-450-Pro

07-02-2011, 01:36 PM	#3 (permalink)
shibby75 Registered Users Join Date: Oct 2010	Have you set your tx to a single servo swash setup? __________________ Hirobo Sceadu 50 - Flymentor 3D KDS 450c - FMA co pilot 2 Kyosho V-one Aurora 9

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

07-02-2011, 02:00 PM	#4 (permalink)
427notch Registered Users Thread Starter Join Date: Jun 2011	I set the tx to Heli- 90 and I have the programer for the Flymentor. The heli is a Copterx with about 80% of the parts beong Align t-rex. The light does go to solid green.

07-02-2011, 03:14 PM	#5 (permalink)
Ivor Hill Registered Users Join Date: Mar 2008	Are the servos plugged in the correct way, signal wire closest to the port numbers ?. Is the FM gyro plugged in the correct way ?. Is there any movement when you operate the sticks. Connect the servo back into your reciever and operate the sticks. Throttle shoud move 1 servo, elevator another servo and aileron the third servo.

07-02-2011, 04:08 PM	#6 (permalink)
427notch Registered Users Thread Starter Join Date: Jun 2011	The tx is not staying on heli-90 it keeps going back to acro. When first hooked it up the motor would not work then I had to plug and play everything to get the controler to work right but my tx is not keeping the heli-90 settings after I take it off the pc. I think im going to have to upgrade the 4 year old radio system to make everything work right.

07-02-2011, 05:40 PM	#7 (permalink)
Jerry Campbell Registered Users My HF Map location Join Date: Apr 2011	I also have a T6 transmitter with the t6config software and there is no choice for a single servo. I have a new transmitter on the way. I'm sure you will have to do the same thing. Good luck Jerry

Register Now

Log-in