Kasama Srimok 90N airframe and $600 in parts

[TJ Present]

Please take a look at my listing on Ebay for the Srimok and tons of parts. For anyone flying a Srimok this is a cost effective way to add a serious stock of spares to your inventory.

http://www.ebay.com/itm/Kasama-Srimo...sAAOSwL7VWo7dY

KSM 10-T27 Torque tube set: $28.00 (2 sets) $56.00
KSM 70-TS04 Crown gear 70T, $23.00 (2 pieces) $46.00
KSM70-TS03 Main gear 98T $26.00
KSM70-FT06 Fuel tank seal rubber $4.00
KSM70-FT02 Fuel tank cap set $5.00
KSM20-T02 Tail rotor shaft steel $8.00
KSM30-111 Thrust bearing d10xD19x5t $11.00
KSM60-079 Titanium frame screw M3x8 (24/pack) upgrade part $14.00
KSM20-C10 Throttle control rod 60mm steel $9.00
KSM30-104 Flange bearing 3x7x3t(4pack) (2 in package) $4.50
KSM40-F04 Landing gear strut clamp (4) $15.00
KSM70-C01 Cyclic damper rubber $7.00
KSM20-TS10 starter coupling steel (new style) $13.00
KSM60-058 spacer 3x5x2.5 (6/pack) $3.00
KSM70-H01 Radius arm Plastic black $6.00
KSM60-043 Stud screw M4 (5/pack) $9.00
KSM10-90H07 Flybar control arm set 4mm $3.00
KSM40-C05 Mount plate servo CF $7.00
KSM20-TS02 Main Mast steel hard $26.00 x2
KSM10-TS01 Upper main bearing block set $18.20
KSM60-004 Button Screw M3x15 (10/Pack) $3.50
KSM20-T03 Spring pin (SPP)set M2x10
KSM60-062 Set screw M3x12 (10/pack) $3.00
KSM60-081 Titanium frame screw M4x34 (2/pack)
KSM30-102 Thurst bearing set d8xD16x5t (2/pack)
KSM60-102 spacer 3x4.8x2.4 (6/pack)
KSM20-C14 Swash plate control rod Stainless steel
KSM60-078 Titanium frame screw M3x32 (24/.pack)
KSM 70-TS06 Clutch Liner Set (2Pcs/Pack)
KSM70-H03 Ball link Plastic black
KSM7002-T08 Shaft drive guide rubber
KSM10-90H06 Collar flybar rod 4mm.set $8.00
KSM20-T03 Spring pin (SPP)set M2x10
KSM 40-F06 Extension GV mount CF $6.00
KSM 10-H11 Washout base ALU $24.00
KSM70-F11 Body support rubber
KSM20-90H01 Spindle shaft set 90 size
KSM60-080 Titanium screw M4x16 $14.00
KSM10-TS18 Tail drive joint rear 5mm $20.00
KSM60-080 Titanium screw M4x16 (Engine damper support) (4/pack) $14.00

[TJ Present]

Leaving nitro and have posted a link to my ebay listing in the "For Sale-Gas and Glow" section. Great Heli and lots of new bagged parts.

https://www.helifreak.com/showthread...10#post6831710

[TJ Present]

Please note this listing is for airframe only and does not include main or tail blades and blade holder.

[TJ Present]

This listing includes a complete air frame plus over $600, of new parts in original Kasama bags as well as a signed business card from Kasama himself. Take a look.

[TJ Present]

Price reduced to $325, for airframe and $600., in new bagged parts!

http://www.ebay.com/itm/Kasama-Srimo...sAAOSwL7VWo7dY

[TJ Present]

Price dropped to $325. If anyone on HF is interested in a trade for this airframe and parts, I am open to that. Please PM. Thanks for looking.

https://www.helifreak.com/showthread.php?t=730361

Tom

[roctopus]

I had the same problem with DX9 , during the bind stage you need to push rudder stick to the right . This solved the problem for me. Also, I needed to dial down settings in normal mode as its very aggressive even using spectrum spm file I hope this helps

[DickT]

Thanks for the suggestion but I have tried every setting in the GT5.2. The pitch and elevator are still incorrect. Swapping channels still produces limited throws on those two channels.

At this time the GT5.2 is on its way back under warranty as it failed. Other GT5.2's I have produce same results. As I mentioned a GT5.1 with 2.0/2.00 firm/software responds correctly.

Going to try it with a Graupner MZ18 next week to see if it works correctly with that system. Meanwhile a MHS Brain is going into the 3 Blader.

[SHOKER]

Sold ?

[hrk175]

Thanks for the input. So what you're basically saying is if I upgrade the battery to a 4s or even a 6s, I will be able to lift a larger amount of weight with the stock motors?
What about getting tri-blade props? Would that increase the payload?

[TJ Present]

Sold