Fun, Learning, Friendship and Mutual Respect
START  HERE


Unregistered
Go Back   HeliFreak > R/C Electronics Support > Mikado V-BAR


Mikado V-BAR Mikado V-Stabi/V-BAR Flybarless System Software and Hardware Support


Reply
 
Thread Tools Display Modes
Old 03-07-2013, 02:31 PM   #1
Dutchdontdance
Registered Users
 
Posts: 64
 

Join Date: Oct 2009
Location: The Netherlands
Default YGE 120LV and vbar governor

Ok, so I got my goblin 500 up and running nicely, slight tail oscillations. These I might be able to dial out with gain, but my vbar log says "governor input glitches" all over the flight, the remainder of the log is ok with good health, no other messages.
I have the YGE 120 LV (vbar ready) and vbar governor active, with internal BEC. So I had my rpm sensor only with the orange wire (which is different from the rpm sensor between my 160HV YGE and vbar on goblin 700) , but I guess I need also the brown (=ground wire), and keep the power (=red wire) out of the rpm sensor port? Could this cause some tail oscillations or bigger problems with more agressive flight (funnels etc.)? I'll change the rpm sensor cable with the ground wire included and report on the result. Appreciate the input, thanks
Jan
__________________
SAB Goblin 700, Scorpion 4525-520, YGE 160 HV, V-bar, Futaba 255 HV/256 HV, Hercules SuperBEC
SAB Goblin 500, Scorpion HK-III 4020-1350, YGE 120 LV, V-bar, Futaba 153/ Savox SB-2272MG
Inverted is the way up
Dutchdontdance is offline        Reply With Quote
Old 03-07-2013, 05:21 PM   #2
Dutchdontdance
Registered Users
 
Posts: 64
Thread Starter Thread Starter
 

Join Date: Oct 2009
Location: The Netherlands
Default YGE 120LV and vbar governor

A picture with the new wiring, will test later..
__________________
SAB Goblin 700, Scorpion 4525-520, YGE 160 HV, V-bar, Futaba 255 HV/256 HV, Hercules SuperBEC
SAB Goblin 500, Scorpion HK-III 4020-1350, YGE 120 LV, V-bar, Futaba 153/ Savox SB-2272MG
Inverted is the way up
Dutchdontdance is offline        Reply With Quote
Old 03-16-2013, 12:43 PM   #3
Dutchdontdance
Registered Users
 
Posts: 64
Thread Starter Thread Starter
 

Join Date: Oct 2009
Location: The Netherlands
Default

Ok, for those interested: I redid my wiring, installed a ferrite ring on the BEC wire of the YGE, and put more space between motor wires and rpm/bec wires from YGE. Result: glitches gone in log! My rpm wire has orange wire only, I removed the ground wire.

As for the tail: I apparently suffered from an issue already noticed in the Goblin 500 forum: the bearing in the tailfin was not glued from factory, so I put some CA on that bearing, tail is rock solid...
__________________
SAB Goblin 700, Scorpion 4525-520, YGE 160 HV, V-bar, Futaba 255 HV/256 HV, Hercules SuperBEC
SAB Goblin 500, Scorpion HK-III 4020-1350, YGE 120 LV, V-bar, Futaba 153/ Savox SB-2272MG
Inverted is the way up
Dutchdontdance is offline        Reply With Quote
Reply




Unregistered
Go Back   HeliFreak > R/C Electronics Support > Mikado V-BAR


Mikado V-BAR Mikado V-Stabi/V-BAR Flybarless System Software and Hardware Support

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


Copyright © 2004-2011 - William James - Helifreak.com