START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
bavarianDEMON/HeliCommand Factory Sponsored Bavarian DEMON and HeliCommand Support |
|
LinkBack | Thread Tools | Display Modes |
07-09-2011, 12:30 AM | #1 (permalink) |
Registered Users
Join Date: Jan 2011
|
Helicommand HC3SX question
Looking for some help setting up heli command
Im just doing my initial set up of heli command HC3SX One of the first steps is to change the endpoints on the radio to match the 100% bars on the programming software. But after finishing with the install ill have to program the ESC, (as i re set the settings in my tx) (castle Ice HV 160) it also requires you to adjust the endpoints for the throttle on your radio. Will these two adjustments not interfere with each other? Thanks |
Sponsored Links | |||
Advertisement |
|
07-09-2011, 03:26 AM | #2 (permalink) |
Registered Users
|
You do not mention if this is an electric or nitro machine, or if your using a Rx or not
When I set mine up, the collective was on the money, so I had no need to change end points. But my understanding is throttle is set separate from collective.
__________________
MSR x1 / mCPX x2 / 450 x4 / Chaos600 test bed / Chaos600 Air-Wolf / American WereWolf 800 / KFrame800/900/1000 / Assorted Fixed Wing JR9303 / JR9503 / Futaba10CHP |
07-09-2011, 10:40 AM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Jan 2011
|
Sorry
Its a Trex 700E No RX just a spektrum satellite I have an RX i could use but it seemed simpler and cleaner to do it without ? Would u recommend using the Rx or just a satellite ? I only had to make slight changes to the endpoints to line up with the software but ya ur right they are different I was just up too late trying to figure it out same stick but different channels ahhah oops |
07-09-2011, 01:53 PM | #4 (permalink) |
Registered Users
|
Make sure your Rx mapping is 100% correct,
I used a AR7100 Rx I know how o wire it up easy enough and everything is installed between the frame set on my helicopter so wiring wasn't an issue for me. I could have just as easily gone without the Rx but I needed the nose weight for my CG
__________________
MSR x1 / mCPX x2 / 450 x4 / Chaos600 test bed / Chaos600 Air-Wolf / American WereWolf 800 / KFrame800/900/1000 / Assorted Fixed Wing JR9303 / JR9503 / Futaba10CHP |
07-09-2011, 02:33 PM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Jan 2011
|
Rx mapping ?
Never done that Is there any advantage that u can see from using the Rx other than the increased diversity from having the rx and the satellite vs just one satellite ? |
07-09-2011, 02:37 PM | #6 (permalink) |
Registered Users
|
Unless its a 450 class bird you will need dual sats.
I just haven't had time to play with that option at present and if it is only single sat ready, I can not use it on my helicopters
__________________
MSR x1 / mCPX x2 / 450 x4 / Chaos600 test bed / Chaos600 Air-Wolf / American WereWolf 800 / KFrame800/900/1000 / Assorted Fixed Wing JR9303 / JR9503 / Futaba10CHP |
07-09-2011, 02:55 PM | #7 (permalink) |
Registered Users
Thread Starter
Join Date: Jan 2011
|
Nice Birds!
It has ports for dual sats and its a 700 so i guess either i pick up another sat for the other side or use the receiver too |
Thread Tools | |
Display Modes | |
|
|