Post your Beastx heli setup here

[salasgr]

Anyone using BeastX on Velo 50N2 flb to post his settings...?

Thanks

[salasgr]

I guess im the only one all over the world flying velocity 50N2 fbl with beastX... ...well, not yet !! i will post mine when time comes


cheers

[Diogenes]

Anyone have beastx settings for X2, 093 and 095 servos?

[Ze Povinho]

Trex 450 Pro V1

Equipment

Scorpion HKII-2221-8 main motor with 15T pinion
Spektrum H3020 servos on cyclic
Futaba S9257 on tail
Align Pro FBL head
Align ESC
DX6i transmitter

Transmitter mode

15 percent expo on aileron and elevator
10 percent expo on rudder
100 percent ATV on aileron, elevator, and rudder (I might experiment with 10 percent more
on aileron and elevator and 5 more for tail)
70 percent gyro gain
0-40-80-80-80 normal mode throttle curve
85 percent flat idle up throttle curve
40-45-50-75-100 normal pitch curve
0-25-50-75-100 idle up pitch curve

Parameter menus

Everything is stock setting with the exception of the following:

B control behavior: transmitter
G cyclic response: slightly increased

Batteries used

Sky Lipo 2200 mAh 40C 11.1V
Gens Ace 2200 mAh 55C 11.1V
Gens Ace 2200 mAh 60C 11.1V

[Wardy1982]

Hello All.

Now got myself a 450 sport v2 with the ar7200bx and i love it. Been reading manuals since i got it second may i add and wondered what settings i should be running on a dx6i with the ar7200bx

Cheers

[RBoyne]

Good day all,
I set up my Trex-600 Pro Nitro using Align Head and parts from Ron's. All seems well except setting my D/r . Should I leave the cyclic with over 12 degree +- or some how reduce those numbers.
If I reduce the travel by the TX it takes from 100% to 20% to get travel within range of normal flight.
I also use a Airtronics SD-10G.
Use of D/r seems to slow the swash movement down is this OK?

[CoolKD]

Align Trex 450 pro V1
MKS DS95 on cyclic
Futaba BLS257 on the tail(tail has the new v3 pitch slider)
Castle ICE 50 set rpm mode @ 3200rpm (3:45 min flight)
Scorpion 2221-6 motor (3s lipo)
KDEdirect head with Align pro FBL grips and swash driver arms
Stock Align 450pro V1 Swashplate
EDGE FBL 325mm V1 blades
Spektrum DSMX satellite on the BeastX

Spektrum DX7
Transmitter mode
30% expo on aileron and elevator
18% expo for the tail
100% ATV for aileron and elevator
80% ATV for the tail
33% transmitter gyro gain (end point menu)

Parameter menus
B control behavior - transmitter
C pitching up behavior - medium (red)
D headlock gain - high (blue flashing)
E stick deadband (default)
F torque precomp (off)

[Cube]

Can anyone post their ATOM500 beastx setup?

[notsobad]

Originally Posted by bryman021

Trex 450 sport w/ DX6I
Converted to fbl with align fbl hub, grips, swash driver, and links.
DS410m on cyclic, DS520 on tail
Stock motor and esc from super combo

Tail gyro gain @ 67 in hh mode
Blue light @ 6 degress, transition from red to blue around 5.75 degrees

All parameter menus at stock setting except B control behavior set to pro

Dial 1 - cyclic gain at 7 o'clock
Dial 2 - direct feed at 9 o'clock (stock)
Dial 3 - tail dynamic at 8 o'clock.

Flies on rails!

could you give tx settings for me?

[CZorzella]

TREX 600E PRO DFC
All stock
Spektrum AR7200BX
Spektrum DX18

Transmitter mode
20% expo on aileron and elevator
15% expo for the tail
110% ATV for aileron and elevator
100% ATV for the tail
55% transmitter gyro gain

Parameter menus
A blue
B blue
C red
D red
E red flashing
F purple
G Blue flashing
H Blue flashing

Throttle Curve
N 0%
1 70%
2 100%
H 16% (Castle ESC – Autorotation Bail-Out - must be adjusted/calibrated for each setup)

Dials
Dial 1 - cyclic gain at maximum positive
Dial 2 - direct feed at 9 o'clock (stock)
Dial 3 - tail dynamic at 6.5 o'clock

.

[Acid Junkie]

T rex 450L Dominator

ESC - hobbywing platinum pro v3 with gov store
motor 460mx align
servos 3x mks ds95 HV + tails ds525 align

beastx plus 4 pro
all servos to highest pulse and hz.....
parameter B to blue (pro) all the rest to default...transmitter gain 30% (beastx to medium 'red') i think....
gov off cause i use the governor of the ESC which is perfect....3680 rpm
attidude control to 3d mode + collective 6 degrees (just to hover and lock the down direction to avoid crash in fast rescue)

heli has over 60 flights....no crash or problem till now....(its my 2nd 450l dominator with the first and the stock parts i had many issues regarding the tail wagging and vibrations)and i blame for that my shopper who after 30 years he dont know that with the governor mode you use a flat line on TC and not something line 0-40-65-75-80 etc.

[andyprima]

Hi, I am setting up an AR7200BX on a T REX 600, nitro and have a problem.

1. when setting the hovering pitch in menu J, the pitch if 6 degrees doesn't seem to save? when I check later it zero - if I move the throttle stick up from mid point to one click above it goes to 6 but not at mid stick?

2. Menu N - pirouette teaching - the swashplate moves whichever option I pick i.e. RED solid or BLUE solid.

Any ideas? I can only think I have set up something wrong on the transmitter - spektrum DX6 ? should I have reversed servos to get the swashplate moving in the right direction - or ignore and leave until all menu items are complete?

I have selected 120 CCPM in menu H (RED solid), with NORMAL in the transmitter.

Any ideas much appreciated, thanks Andy

[andyprima]

Hi, I cannot get the set up to save the 6 degrees of pitch in menu j. At the end of setup, its at zero pitch. And, I cannot get the final set up pirouette rate to work - whichever I pick, red or purple the swashplate moves as i rotate the helicopter. Any ideas?

[Skiddz]

Originally Posted by andyprima

Hi, I am setting up an AR7200BX on a T REX 600, nitro and have a problem.

1. when setting the hovering pitch in menu J, the pitch if 6 degrees doesn't seem to save? when I check later it zero - if I move the throttle stick up from mid point to one click above it goes to 6 but not at mid stick?

2. Menu N - pirouette teaching - the swashplate moves whichever option I pick i.e. RED solid or BLUE solid.

Any ideas? I can only think I have set up something wrong on the transmitter - spektrum DX6 ? should I have reversed servos to get the swashplate moving in the right direction - or ignore and leave until all menu items are complete?

I have selected 120 CCPM in menu H (RED solid), with NORMAL in the transmitter.

Any ideas much appreciated, thanks Andy

Originally Posted by andyprima

Hi, I cannot get the set up to save the 6 degrees of pitch in menu j. At the end of setup, its at zero pitch. And, I cannot get the final set up pirouette rate to work - whichever I pick, red or purple the swashplate moves as i rotate the helicopter. Any ideas?

Please do not cross-post. The thread you created in the Main forum has been merged with this one.

[sutty]

Originally Posted by andyprima

Hi, I am setting up an AR7200BX on a T REX 600, nitro and have a problem.

1. when setting the hovering pitch in menu J, the pitch if 6 degrees doesn't seem to save? when I check later it zero - if I move the throttle stick up from mid point to one click above it goes to 6 but not at mid stick?

2. Menu N - pirouette teaching - the swashplate moves whichever option I pick i.e. RED solid or BLUE solid.

Any ideas? I can only think I have set up something wrong on the transmitter - spektrum DX6 ? should I have reversed servos to get the swashplate moving in the right direction - or ignore and leave until all menu items are complete?

I have selected 120 CCPM in menu H (RED solid), with NORMAL in the transmitter.

Any ideas much appreciated, thanks Andy

Hi Andy

Set-up step J has nothing to do with hovering pitch. If you think this, then you must not have a set of proper instructions to follow. I suggest downloading a full version from BeastX for their MicroBeast. Although it will include a section on receiver type, of which you have no choice, just ignore that part, and everything else will be covered in much more detail.

If after going through this alternate manual, you still have questions, create a thread about your issue in the BeastX FBL system forum.

This thread is dead, and was for posting your completed BeastX set-ups, so others could see what worked.