Register Now

Scraggy · 09-03-2010, 12:59 PM

Of this is annoying, i have purchased the new bearing set as shown and on the discription that arrived with my new bearings and hub it shows the new bearings on the inside, however the elyQ web site PDF is different showing them on the outside, anbody shed any light on the subject please........

http://www.elyq.com/pdf/news/a_bearing.pdf

Scraggy

alexmit · 09-03-2010, 03:09 PM

Mine are mounted on the outside per the PDF. Just make sure the red shield is pointed toward the hub and not the blade. If you are using the metal tail grips, watch out for the large diameter washer. I had to file the outer edge of mine slightly so the bearings would seat completely into the grip. This would be the large diameter washer as shown on Tail rotor hub SUS V2 that goes between the bearings.

Scraggy · 09-03-2010, 05:02 PM

I just got the even newer hub, the V2.01 man the clearly dident get this right did they. anyway this one is the last on the page, I have the metal grips and a standard set of bearings, and the new angular, which i assume replaces the thrust washer set.

I wish they had been a bit clear about this one, i had the original tail which started binding and almost fell apart in flight. my first disapointment i think with this heli.

going to go with final diagram, and see how well it works.

scraggy

Geffect · 09-03-2010, 08:27 PM

Id suggest posting this on the elyq.info forum as the Elyq staff will be able to answer your questions and forward the info. onto the appropriate people i.e. fix the documentation.

Scraggy · 09-05-2010, 10:57 AM

Guys,

Anbody got the metal tail and angular bearings would appriciate some advice.

Scraggy

alexmit · 09-07-2010, 03:35 PM

I'm really not sure what you are getting at. The pictures you linking to are correct.
As far as posting in the ElyQ forum... have fun with that one. I found it pretty useless and unresponsive.

09-03-2010, 12:59 PM	#1 (permalink)
Scraggy Registered Users My HF Map location Join Date: Dec 2008	Angular Bearing assembly Of this is annoying, i have purchased the new bearing set as shown and on the discription that arrived with my new bearings and hub it shows the new bearings on the inside, however the elyQ web site PDF is different showing them on the outside, anbody shed any light on the subject please........ http://www.elyq.com/pdf/news/a_bearing.pdf Scraggy __________________ helicopterpilot@btinternet.com

09-03-2010, 05:02 PM	#3 (permalink)
Scraggy Registered Users Thread Starter My HF Map location Join Date: Dec 2008	Thanks I just got the even newer hub, the V2.01 man the clearly dident get this right did they. anyway this one is the last on the page, I have the metal grips and a standard set of bearings, and the new angular, which i assume replaces the thrust washer set. I wish they had been a bit clear about this one, i had the original tail which started binding and almost fell apart in flight. my first disapointment i think with this heli. going to go with final diagram, and see how well it works. scraggy __________________ helicopterpilot@btinternet.com

09-05-2010, 10:57 AM	#5 (permalink)
Scraggy Registered Users Thread Starter My HF Map location Join Date: Dec 2008	Anbody Out there Guys, Anbody got the metal tail and angular bearings would appriciate some advice. Scraggy __________________ helicopterpilot@btinternet.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-03-2010, 03:09 PM	#2 (permalink)
alexmit Registered Users Join Date: Jan 2007	Mine are mounted on the outside per the PDF. Just make sure the red shield is pointed toward the hub and not the blade. If you are using the metal tail grips, watch out for the large diameter washer. I had to file the outer edge of mine slightly so the bearings would seat completely into the grip. This would be the large diameter washer as shown on Tail rotor hub SUS V2 that goes between the bearings.

09-03-2010, 08:27 PM	#4 (permalink)
Geffect Registered Users Join Date: Apr 2010	Id suggest posting this on the elyq.info forum as the Elyq staff will be able to answer your questions and forward the info. onto the appropriate people i.e. fix the documentation.

09-07-2010, 03:35 PM	#6 (permalink)
alexmit Registered Users Join Date: Jan 2007	I'm really not sure what you are getting at. The pictures you linking to are correct. As far as posting in the ElyQ forum... have fun with that one. I found it pretty useless and unresponsive.

Register Now

Log-in