START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Scale Projects <790 Scale Projects <790 Discussion |
|
LinkBack | Thread Tools | Display Modes |
04-16-2008, 08:02 PM | #1 (permalink) |
Registered Users
|
Heli Artist Air Wolf w/retracts
While I'm waiting for the rest of the stuff I need for my Sea King project, I decided to go ahead and work on my new Heli Artist Air Wolf. I got the black and white one with the retract system.
Opening the box, I was pleasently surprized by what was found inside. The fuselage was beautiful, the windshield was wrapped in tissue, the wood parts,tail fins, hardware and landing gear control rods were separately bagged. Even a bottle of CA was included! The landing gear was all ready mounted to the fuselage and the control horns were in place, but not secured (that comes later). The landing gear struts appear to be aluminum that was cut with a water jet machine and are VERY nice. The entire nose comes off for easy access and battery changes. It is held in place by magnets and "keying tabs". Very simple and effective. The only disappointment was the instruction (and I use that term VERY loosely) sheet. This consisted of an 8x11 sheet, printed both sides with some pictures and very poor English directions. Pictue 1 shows how everything came out of the box Picture 2 shows how the main gear strut is attached in the fuselage Picture 3 shows the main strut (MUCH nicer than bent wire) Pictue 4 shows the nose gear (sorry about the focus) I spent last night finsihing the rebuild of the T-Rex from my last "oops" and started programing my new Futaba 12Z FASST system. I'm going to get started on setting up the landing gear linkages to night. Heli Artist, if you are listening, PLEASE bring the instruction sheets up to the same level of quality as the fuselage. More to come...........
__________________
Larry R. Rogers Helinut 1st Class B.O.S.S. member "Dragon Balls" |
Sponsored Links | |||
Advertisement |
|
04-16-2008, 08:12 PM | #2 (permalink) |
Registered Users
|
Looks nice. Those wheel struts definitely look a lot nicer than the bent wire struts on my Fusano.
__________________
Brent 2-D Scale Flyer AMA #35431 |
04-16-2008, 08:38 PM | #3 (permalink) |
Registered Users
Join Date: Oct 2006
|
Looks nice! Who is stocking those?
|
04-16-2008, 09:56 PM | #4 (permalink) |
Registered Users
Thread Starter
|
I ordered it from www.flying-hobby.com out of Hong Kong. I took about ten days to reach my door.
__________________
Larry R. Rogers Helinut 1st Class B.O.S.S. member "Dragon Balls" |
04-17-2008, 01:06 AM | #5 (permalink) |
Registered Users
|
Nice post, those retracts look real nice. If you ever crash the thing I'll take the retracts of you
__________________
Outrage G5 Skookum Flybarless T-Rex 500esp V-Bar flybarless Outrage 550 - T-Rex 600 Nitro Pro DMHC |
04-17-2008, 06:51 AM | #6 (permalink) |
Registered Users
Thread Starter
|
Well Andy, considering the fact that I have three confimed "kills" and all were with the T-Rex, that might not be out of the question!
Last night, I hooked up the landing gear per the directions and using the supplied hardware. It works, but was a bit of a pain trying to CA the wooden control arms to the strut axles without getting it on the one piece ball links. If I ever have to redo this, I'll opt for standard 2 piece ball links and/or nylon control horns secured with set screws. I think that would be MUCH easier to set up and adjust. Now don't get me wrong, the supplied parts work, they are just a bigger pain to deal with then they need to be. Next step is mount the servo.......
__________________
Larry R. Rogers Helinut 1st Class B.O.S.S. member "Dragon Balls" |
04-17-2008, 01:04 PM | #7 (permalink) |
Registered Users
|
I looked for control arms with set screws but couldnt find any - the causemann retracts also were pants in that department. Have you seen any? I'm still up for some to improve my set, just in the interim while I wait for your carnage
Andy
__________________
Outrage G5 Skookum Flybarless T-Rex 500esp V-Bar flybarless Outrage 550 - T-Rex 600 Nitro Pro DMHC |
04-17-2008, 01:09 PM | #8 (permalink) |
Registered Users
Thread Starter
|
No offense Andy, but I hope you have a long time for any carnage to take place!
I haven't seen the set you mentioned. In the Darth styrene fuselages, the maker shows how to make the horns using a standard servo horn with a wheel collar CA'ed inplace of the servo shaft. Just drill a hole for the set screw. I wish now that I had tried that.
__________________
Larry R. Rogers Helinut 1st Class B.O.S.S. member "Dragon Balls" |
04-17-2008, 03:55 PM | #9 (permalink) |
Registered Users
|
__________________
Outrage G5 Skookum Flybarless T-Rex 500esp V-Bar flybarless Outrage 550 - T-Rex 600 Nitro Pro DMHC |
04-17-2008, 04:36 PM | #10 (permalink) |
Registered Users
Thread Starter
|
AHHHH. Those are very similar to the Fusuno retracts.
__________________
Larry R. Rogers Helinut 1st Class B.O.S.S. member "Dragon Balls" |
04-17-2008, 08:42 PM | #11 (permalink) |
Join Date: Apr 2008
|
I too recently ordered the Heli-Artist AirWolf with retracts. It arrived a few days ago. I also ordered the CNC retract upgrades, but will install them later. Trying to get at the two back retracts looks like more work than its worth. Right now I'm trying to figure out the mounting blocks. According to step five I'm supposed to "Drew holes under the body". What is shown to be installed on the heli frame in one picture conflicts with what is listed in step 12. Anybody have some pictures or info on this area of construction ?
Cheers |
04-17-2008, 09:05 PM | #12 (permalink) |
Registered Users
Thread Starter
|
I feel your pain! I had hoped to start that part of the build tonight, but during radio testing I found that the tail boom was slipping. I'm going to drill out the frame blocks and use through bolts; that should end that problem!
When I mounted the new Kong Power battery, I discovered that were quite a bit thicker than the packs they replaced. That meant I had to change the placement of the electronics from what I had planned. So basically, I'm back to where I was a couple days ago. On the plus side, The programing I did on the new radio was correct, everything moved the way it was suppsed to!
__________________
Larry R. Rogers Helinut 1st Class B.O.S.S. member "Dragon Balls" |
04-18-2008, 12:04 AM | #13 (permalink) | |
Registered Users
|
Quote:
The system for the rear wheels, in the HeliArtist fuselage, would probably not survive removal. The Fusuno retract system would be easier to acquire and install in the non-retract HeliArtist version fuselage. |
|
04-18-2008, 01:28 AM | #14 (permalink) |
Registered Users
|
Hey nice photos, can you give me an idea how sturday the front tray is in each set? Is there any flex with the weight of the heli on the fron strut? I had to brace the causemann tray against the frame to stop it bowing upwards when the heli is on the gound.
Is one set better than the other in that respect?
__________________
Outrage G5 Skookum Flybarless T-Rex 500esp V-Bar flybarless Outrage 550 - T-Rex 600 Nitro Pro DMHC |
04-18-2008, 10:35 AM | #15 (permalink) |
Registered Users
|
I have not built the HeliArtist Airwolf yet, I just received it yesterday, I am waiting on the CNC retract upgrade parts that I just ordered after receiving the fuselage.
On the Fusuno Airwolf, the flexing did not affect the operation of the retracts. With the battery mounted on the lower tray, and a Velcro strap under the tray and around the battery, flexing of the retract tray was minimized. Last edited by BlackTitanium; 04-18-2008 at 01:35 PM.. |
04-19-2008, 10:43 PM | #16 (permalink) |
Join Date: Jul 2007
|
Hey Titanium - are you going to be building the non-retract version fuselage w/the fusuno retract kit?
|
04-20-2008, 01:55 PM | #18 (permalink) |
Join Date: Jul 2007
|
I have the Airwolf non-retract version (V2) along with the fusuno retract kit - do you think I would be better off selling this and getting the kit with the retracts? This will be my first scale model - thanks so much.
|
04-20-2008, 05:48 PM | #19 (permalink) |
Join Date: Apr 2008
|
Well, after staring at the empty fuse for two days I decided to use the CNC retracts after all. The process took a little over 2 hours to complete but I am glad with the new CNC parts. They are definitely easier to set up. No more CA, just a bit of blue loctite. I did have to break the existing CF rods to get the old retracts out. Also, the rear wheels needed a small spacer between the aluminum strut and the wood side. Now I need to figure out a way to mount the frame to the fuse so that it is still easy to remove later on. Does anybody with this setup have any pictures available ? Not sure on how many of the wood blocks to use, placement, or attachment methods to use.
|
04-20-2008, 08:49 PM | #20 (permalink) |
Registered Users
Thread Starter
|
Vince, I spent most of the day yesterday trying to figure out to make all the parts fit using the included "directions". I finally said the heck with and tossed the directions. Here is what I did:
1. I noticed that the front wooden mount would be sitting on the wood work for the retracts. So I glued two pieces (one with the small slots and one with the larger slots) together for the rear support. 2. Next, I scuffed up the interior with some 100 grit paper and ran CA around the landing gear support "tongue". When the glue was dry, I removed the two inboard nuts/bolts. 3. I then took one of the "soild"wood pieces (marked "assembly on the fuselage" on the instruction sheet) and drilled them to suit the mounting holes (where the skids mounted) on the frames. 4. I attached the wood piece to the frames with the strut mounting screws. I then inserted the frames into the fuselage and positioned it so the main shaft was centered in it's opening. 5. Now the tricky part. Holding everything steady, I turned the fuselage over and screwed two of the washer head screws supplied with the kit through the holes that the nut/bolts that I removed in step 3 were in. This secured the wood mounting piece the landing gear woodwork. Now remove those screws, remove the mechanics and remove the wood piece from the frames. 6. Now, take that wood piece and re-attach it to the landing gear wood work with the two screws. I then used CA to permanently attach the wood piece. While the glue was drying, I cut a template from poster board for all four mounting screws. 7. Using the proper sized bit in my Dremel, I drilled the front mounting holes through the fuselage using the wood mounting piece as a guide. 8. I then ran two screws through the template and through the holes just drilled. I smoothed it out (gently) and secured it with masking tape. I then marked and drilled the aft mounting holes and removed the template. 9. I mounted the doubled aft block and used the template on the iside to double check that all was well. When I was satisfied, I CA'd the block in place. 10. The acid test! I fit the machanics and screwed it in with some longer screws I had in my "left-over-parts-bin". It's a bit of a pain to get the last screw in the proper place, but it works! After finishing that test fit, I removed the screws so I could slide the mechanics further back so I could reassemble the tail rotor. After that was complete, I pulled the mechanics forward to the mounting point and discovered the tail boom would need to be "relieved" a bit so the tail rotor bell crank had enough clearance. That was where I stopped last night and haven't had a chance to get back on it today. Hopefully, this and the pics will give you an idea how I attacked the problem.
__________________
Larry R. Rogers Helinut 1st Class B.O.S.S. member "Dragon Balls" |
Tags |
air wolf |
Thread Tools | |
Display Modes | |
|
|