Register Now

JWeber · 02-22-2015, 04:05 PM

Do you need to reset the end points when you update the firmware on your ESC? Just curious. I have some odd behavior and was wondering if that might cause it.

nu66ie · 02-23-2015, 02:09 PM

What ESC are you using? I too have had some issues after updating an 130 Opto a couple of days ago.

JWeber · 02-23-2015, 04:20 PM

Commander 50V 90A (OPTO)

The reason I ask is that I was having an issue with startup. I set the end points as one of the first things that I did, but I got the USB cable and decided to flash the firmware. I didn't redo the end point setting and I could only get the heli to start up in IU 2. Once it was started, I could switch to IU 1 or Normal at lower gov speeds on my Ikon and it would work fine.

I redid the end point setting yesterday but have not flown it since and will not get a chance until at least Saturday to try it out.

Michaelinpr · 03-06-2015, 03:34 AM

I always reset the throttle limts when doing updates. I will also check and likely redo the settings that I programmed just to be sure everything is where I want it.

508NATE · 03-28-2015, 07:34 PM

how did you make out with the test flight?

JWeber · 03-28-2015, 07:40 PM

Everything went well. The goblin is a lot of fun.

02-22-2015, 04:05 PM	#1 (permalink)
JWeber Registered Users Join Date: Mar 2012 Location: Wauwatosa, WI	End Point Setting Do you need to reset the end points when you update the firmware on your ESC? Just curious. I have some odd behavior and was wondering if that might cause it. __________________ Specter v2, Tron Dnamic, Nimbus 550, P380, Edge-TX

02-23-2015, 02:09 PM	#2 (permalink)
nu66ie Registered Users Join Date: Apr 2011	What ESC are you using? I too have had some issues after updating an 130 Opto a couple of days ago. __________________ Goblin 630, T-Rex 700e, Outrage Fusion 50, all with VBar, Blades MCX2, 120SR, Radian Pro, DX8's - HeliBuilderNM

02-23-2015, 04:20 PM	#3 (permalink)
JWeber Registered Users Thread Starter Join Date: Mar 2012 Location: Wauwatosa, WI	Commander 50V 90A (OPTO) The reason I ask is that I was having an issue with startup. I set the end points as one of the first things that I did, but I got the USB cable and decided to flash the firmware. I didn't redo the end point setting and I could only get the heli to start up in IU 2. Once it was started, I could switch to IU 1 or Normal at lower gov speeds on my Ikon and it would work fine. I redid the end point setting yesterday but have not flown it since and will not get a chance until at least Saturday to try it out. __________________ Specter v2, Tron Dnamic, Nimbus 550, P380, Edge-TX

03-06-2015, 03:34 AM	#4 (permalink)
Michaelinpr Registered Users Join Date: Mar 2009 Location: Puerto Rico (but i am Canadian)	I always reset the throttle limts when doing updates. I will also check and likely redo the settings that I programmed just to be sure everything is where I want it. __________________ Scorpion Power Systems www.onlyfinehelis.com

03-28-2015, 07:40 PM	#6 (permalink)
JWeber Registered Users Thread Starter Join Date: Mar 2012 Location: Wauwatosa, WI	Everything went well. The goblin is a lot of fun. __________________ Specter v2, Tron Dnamic, Nimbus 550, P380, Edge-TX

03-28-2015, 07:34 PM	#5 (permalink)
508NATE Registered Users Join Date: Dec 2012	how did you make out with the test flight?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in