START HERE |
|
Register | FAQ | PM | Events | Groups | Blogs | Calendar | Mark Forums Read |
Unregistered
|
Master CP Walkera Master CP Helicopter Support |
|
LinkBack | Thread Tools | Display Modes |
02-25-2015, 11:44 PM | #1 (permalink) |
Registered Users
Join Date: Feb 2015
|
Tail motor pinion gear Replacement
Has anyone replaced the Tail motor pinion gear. After a crash looks like a lost one tooth on the motor pinion gear. I have the replacement but have no idea how to get that little one off and the new one back on.
|
Sponsored Links | |||
Advertisement |
|
02-28-2015, 12:36 AM | #2 (permalink) |
Registered Users
Join Date: Feb 2014
|
Hi Astrokc1
You will need a .9 mm hex tool to remove the tail gear , it's a pain but can be done you may find some locktight on the thread so take your time the rest is pretty straight forward Hope this helps Cheers watho
__________________
Master CP devo 7E Walkera 450 DO3 Blade 4503D conv to FBL Spectrum DX6i Building 550x and a phoenix sim fly,crash,order parts,repair and repeat |
02-28-2015, 03:05 PM | #3 (permalink) |
Registered Users
Thread Starter
Join Date: Feb 2015
|
Im talking about the motor gear not the blade gear.
Watho I think your the only person that ever offers a reply after 36 people viewed this question. Im talking about the motor gear the little one attached to the tail motor.
|
03-01-2015, 02:37 AM | #4 (permalink) | |
Registered Users
Join Date: Feb 2014
|
Quote:
Just come down to the work bench to have a look and it looks like it is pressed on, so you may need some sort of gear pulley or be inventive I would say it should not take much to get off but I have never removed one Sorry OK just had a play on the bench,I use a pulley to get the gear off, comes off easy,but I used a pulley, not a great deal of effort but a little, Possible could be done with pliers or similar Hope this helps enjoy your flying Cheers watho Sorry to get the new one on I just placed it on the bench (square or 90*) placed a bit of cloth over it (doubled or tripled) and gave it a tap (small hammer or large pliers) Cheers watho
__________________
Master CP devo 7E Walkera 450 DO3 Blade 4503D conv to FBL Spectrum DX6i Building 550x and a phoenix sim fly,crash,order parts,repair and repeat Last edited by watho 46; 03-01-2015 at 02:42 AM.. Reason: Extra thought |
|
03-01-2015, 08:09 AM | #5 (permalink) |
Registered Users
Thread Starter
Join Date: Feb 2015
|
Thanks Again for the reply
I will give it a shot, I will let you know how it goes. Might be a few days before I try it.
|
03-28-2015, 05:29 PM | #6 (permalink) |
Registered Users
Thread Starter
Join Date: Feb 2015
|
tail motor pinion gear
Well, I don't see any way to replace the pinion gear on the motor. Tried to yank the gear of with pliers, all it did was break the nylon gear portion. tried to use pliers to remove the remaining aluminum portion that was left on the shaft with pliers , also did not work. Used heat and that removed the remaining portion of the gear. Tried to lightly tap the new gear on the shaft NO way would it go on, and in fact broke the opposite side of the motor loose from the housing. For grins already ruined the motor tried to heat the shaft and push the gear on and all it did was melt the nylon on the new gear. Oh well I tried.
|
03-30-2015, 04:37 PM | #7 (permalink) |
Registered Users
Join Date: Feb 2014
|
Hi astrokc1
Mon sorry to hear ,I had little problem getting mine off So I guess it's back to ordering parts If you need anymore help just post I'm hear from time to time Cheers watho
__________________
Master CP devo 7E Walkera 450 DO3 Blade 4503D conv to FBL Spectrum DX6i Building 550x and a phoenix sim fly,crash,order parts,repair and repeat |
Thread Tools | |
Display Modes | |
|
|