Register Now

heathy · 09-27-2012, 05:38 PM

Some one please ban the compass workers from using it, looking at it or even being in the same room as it

In the middle of building another 7hv and its bad, real bad. Never seen so much white dried mess

PLEASE LEAVE ALL BOLTS LOOSE AND DRY

dannylightning · 09-27-2012, 06:13 PM

sounds like i must work there. lol.. i tend to use to much loc tite... but i am working on that

heathy · 09-27-2012, 06:30 PM

Danny, i doubt you'd use this much, should have taken a pic. 1 of the feather shaft bolts was covered. 3 of the motor mount bolts covered and the slot in the cf too.
When i backed them out white dry powder rained down like snow.

All swash bolts had none, now red loctite on there.

Basically its a mess and so far i've spent about a hour cleaning it off, which isn't the easiest job to do.

Would be better for the factory to either give us the kit flat pack or ban thread lock and tell us to do it ourselves.

Caleb White · 09-28-2012, 09:36 AM

That sucks. So why not stop pulling them after a few, and just leave in until it is necessary to remove?

heathy · 09-28-2012, 09:45 AM

I would do but can't trust them! Plus the motor mount had to be removed. Gaui don't use it in their kits.

09-27-2012, 05:38 PM	#1 (permalink)
heathy Registered Users Join Date: Apr 2010	Thread lock Some one please ban the compass workers from using it, looking at it or even being in the same room as it In the middle of building another 7hv and its bad, real bad. Never seen so much white dried mess PLEASE LEAVE ALL BOLTS LOOSE AND DRY __________________ Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep

09-27-2012, 06:13 PM	#2 (permalink)
dannylightning Registered Users My HF Map location Join Date: Jun 2010	sounds like i must work there. lol.. i tend to use to much loc tite... but i am working on that __________________ ----------------------------------------------------------------- Blade 180 CFX, Sold the rest of my stuff, I dont really fly all that often any more.

09-27-2012, 06:30 PM	#3 (permalink)
heathy Registered Users Thread Starter Join Date: Apr 2010	Danny, i doubt you'd use this much, should have taken a pic. 1 of the feather shaft bolts was covered. 3 of the motor mount bolts covered and the slot in the cf too. When i backed them out white dry powder rained down like snow. All swash bolts had none, now red loctite on there. Basically its a mess and so far i've spent about a hour cleaning it off, which isn't the easiest job to do. Would be better for the factory to either give us the kit flat pack or ban thread lock and tell us to do it ourselves. __________________ Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep

09-28-2012, 09:36 AM	#4 (permalink)
Caleb White Registered Users My HF Map location Join Date: Nov 2006	That sucks. So why not stop pulling them after a few, and just leave in until it is necessary to remove? __________________ What a great hobby...even better, its people! Be blessed, friends.

09-28-2012, 09:45 AM	#5 (permalink)
heathy Registered Users Thread Starter Join Date: Apr 2010	I would do but can't trust them! Plus the motor mount had to be removed. Gaui don't use it in their kits. __________________ Oxy 3 SK540 Minijazz 20 / WARP 360 SK540 Koby 55 / Goblin 500 SK540 jive 100 / 6HV ultimate Helijive120 SK540 / 7HV SK540 Kosmik200 / Futaba18mz / Skookum support rep

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register Now

Log-in